Daikin DCM601A51 Скачать руководство пользователя страница 105

Страница: 105 / 344

User’s Manual EM11A015B

intelligent Touch Manager

104

•

Ventilator Tab (Events Screen)

This screen is displayed when you touch the Ventilator tab on the Events screen.

Sets up the Ventilator actions.

(1)

(2)

(3)

(4)

Select the check box of the items to set up and select the setting from the combo box.

(1)

Ventilation Mode setting

area

Sets up the ventilation mode.

Select the setting from Automatic, ERVentilation, and Bypass.

(2)

Ventilation Amount setting

area

Sets up the ventilation amount.

Select the setting from Auto (normal), Low (normal), High (normal), Auto (fresh up), Low (fresh

up), and High (fresh up).

(3)

button

Saves the edit and closes the screen.

(4)

Cancel

button

Cancels the edit and closes the screen.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды