Daikin DCM601A51 Скачать руководство пользователя страница 85

Страница: 85 / 344

User’s Manual EM11A015B

intelligent Touch Manager

•

Schedule Confirmation Screen

This screen is displayed when you touch the Confirm button on the Schedule screen.

It allows you to check the setting details of schedule programs with the Schedule Settings list.

(1)

(3)

(2)

(4)

(5)

(1)

Schedule Settings

list

Displays the list of events for the date indicated in the Date area

(2)

for the selected schedule

program.

(2)

Date

area

Displays the date and day of the week for which the events are displayed.

(3)

Back

button

Changes the content displayed in the Schedule Settings list to that of the previous day.

(4)

Next

button

Changes the content displayed in the Schedule Settings list to that of the next day. You can

specify up to the next 7 days.

(5)

Close

button

Closes the screen.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды