Daikin DCM601A51 Скачать руководство пользователя страница 230

Страница: 230 / 344

User’s Manual EM11A015B

intelligent Touch Manager

229

10.

Power Proportional Distribution

10-1

Power Proportional Distribution Function

Power Proportional Distribution is a function that proportionally distributes the total power used by

the air conditioners in a rental building and the like, measured using an electricity meter among the

tenants. The proportional distribution calculation can also be exported to a CSV file.

For the USB memory requirements, see “Peripheral Equipment Specifications (CB14A005).”

To use this function, you must set up groups for proportional distribution, input devices, etc. as well

as run a trial on a PC in advance. Consult your service person.

Proportional distribution cannot be calculated if the controller is turned off. Do not turn off the

controller if calculating proportional distribution.

This chapter describes operations to be performed on the iTM unit.

The iTM is designed to measure the accumulated value using a pulse-output accumulator installed

to the mains power supply line for an air conditioner and calculate the distribution (proportional

distribution) value based on the estimated load ratio for each indoor unit.

Setting up the data collection period

Touch the PPD button on the Operation Mgmt. tab of the Menu List screen and display the Power

Proportional Distribution screen (see “4-5 Menu List Screen: Operation Mgmt. Tab”).

(1)

(2)

(a)

(b)

Set the data collection period in

(1)

Select the

Period

radio button

(a)

to set the collection start and end dates.

Touch the Modify button for Start date and End date, and enter the dates in the respective Date

Input dialog that appears.

Operating Optional Maker Functions

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды