Daikin DCM601A51 Скачать руководство пользователя страница 300

Страница: 300 / 344

User’s Manual EM11A015B

intelligent Touch Manager

299

<About Power Proportional Distribution function>

■

“PPD” icon is not displayed.

The Power Proportional Distribution function is not enabled. Consult your authorized dealer.

■

About standby power

“Standby power” in the Power Proportional Distribution result displays the total of the crank case

heater power consumed by an air conditioner in a standby state, because it cannot be distributed

to any other air conditioner when it is set up not to distribute the power.

This total power needs to be separately handled as common utility expenses etc.

■

To display the power consumption by tenant

The iTM unit displays the power consumption by air conditioner or by area in the Power

Proportional Distribution result.

■

To convert the power consumption into power charges

The iTM unit does not support the conversion of the power consumption into power charges.

■

To print the Power Proportional Distribution result

The iTM unit does not have the print function.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды