Daikin DCM601A51 Скачать руководство пользователя страница 132

Страница: 132 / 344

User’s Manual EM11A015B

intelligent Touch Manager

131

The Type of the management point is displayed in

(3)

. However, you cannot change it here.

Touch the Modify button

(4)

for the management point name. Enter the new name in the Text

Input dialog box that appears. The number of characters you can enter is 1 to 12, irrespective of

single or double byte.

If the entered name is duplicated, a dialog with the message “Same Mgmt. Point name is already

registered” appears and it is rejected.

Touch the Modify button

(5)

for Detailed Info. Enter the detailed information in the Text Input

dialog that appears. The maximum number of characters you can enter is 50, irrespective of

single or double byte. You can omit entering detailed information if there is nothing to enter.

To set up the icon

(6)

, touch the Modify button and display the Icon Setup screen.

(7)

Select an icon from

(7)

and touch the OK button to set it up. Return to the Mgmt. Points

Attributes Setup screen to check the whole view and touch the OK button to close the screen.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды