Daikin DCM601A51 Скачать руководство пользователя страница 40

Страница: 40 / 344

User’s Manual EM11A015B

intelligent Touch Manager

(7)

LAN LINK (Green)

This LED indicates whether the LAN connection between the intelligent Touch Manager and the

connected hardware is correct. The LED is On when the connection is correct.

(8)

DIII MONITOR (Yellow)

This LED flashes when data transmission occurs on the DIII-NET communication line.

(9)

MONITOR key/LED (Orange/Green)

Press this switch to turn on/off the monitor. Doing so also causes the LED color to change as

follows.

Off

: Indicates that the power is off.

On (Orange)

: Indicates that the monitor is on.

On (Green)

: Indicates that the monitor is on.

(10)

RESET//

Restart switch for restarting the intelligent Touch Manager.

(11)

USB socket cover (side)

USB memory port.

Do not use the socket for any purpose other than connecting a USB memory.

NOTE

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды