Daikin DCM601A51 Скачать руководство пользователя страница 109

Страница: 109 / 344

User’s Manual EM11A015B

intelligent Touch Manager

108

Cautions when Using Simultaneously with Other Control Functions

Start/Stop of air conditioners by the Heating Mode Optimization function does not affect the

operation of this function.

If the Pre-Cool/Pre-Heat function is simultaneously set up, the air conditioners may be stopped

before the time set up by this function, preventing the temperature to reach the setpoint at the

set time.

Example: 1. Duration is set to 30 minutes.

2. Pre-Cool/Pre-Heat is enabled to achieve 20°C at 9:00 by schedule.

3. The air conditioners are automatically started at 8:15 by the Pre-Cool/Pre-Heat

function.

4. This function stops the air conditioners at 8:45. Therefore, the air conditioners are

stopped by 9:00, the time set in the schedule.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды