Daikin DCM601A51 Скачать руководство пользователя страница 209

Страница: 209 / 344

User’s Manual EM11A015B

intelligent Touch Manager

208

The following describes how to set this up.

Touch the HMO button on the Automatic Ctrl. tab of the Menu List screen and display the

Heating Mode Optimization Settings screen (see “4-5 Menu List screen: Automatic Ctrl. Tab”).

(1)

(2)

(3)

(4)

2. Select an indoor unit from list

(1)

displaying the names of indoor units and whether this function

is enabled or disabled, and then select Enable or Disable in

(2)

Touching the

Enable All

button

(3)

enables all listed indoor units.

Touching the

Disable All

button

(4)

disables all listed indoor units.

When finished, touch the Close button and close the screen.

Cautions when Using Simultaneously with Other Control Functions

Start/stop of indoor units by this function becomes the input condition for the Interlocking Control

function.

Since indoor units stopped by this function are recognized as operating by the iTM, they are also

not recognized as “stopped” by other functions such as Central Monitoring, Timer Extension,

History, etc.

When an indoor unit stopped by this function is started by remote controller, it is stop at the next

room temperature assessment if the room temperature exceeds the setpoint in 1°C or more.

Indoor units stopped by this function are treated as Stopped for Power Proportional Distribution

and the current consumed while stopped, calculated as Idle Power.

This function cannot stop indoor units in operation by the Temperature Limit function.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды