Daikin DCM601A51 Скачать руководство пользователя страница 87

Страница: 87 / 344

User’s Manual EM11A015B

intelligent Touch Manager

•

Weekly Pattern Tab (Schedule Edit Screen)

This screen is displayed when you touch the Weekly Pattern tab on the Schedule Edit screen.

It allows you to set up a weekly schedule.

(1)

(2)

(3)
(4)

(5)

(6)

(8)

(7)

(1)

Day of the week

radio button

Selects the day of the week to edit.

(2)

Schedule Settings

view

Displays the schedule set to each day of the week.

(3)

Copy

button

Displays the Copy to Selection screen for selecting the destination, to which the schedule set for

the day of the week, selected with the radio button, will be copied.

(4)

Delete

button

Deletes the schedule set to the day of the week selected with radio button. Touching the button

displays a deletion confirmation dialog.

(5)

Edit

button

Displays the Event List screen that allows you to edit the schedule set up for the day of the week

selected with the radio button.

(6)

Legend

view

Displays legends available in the Schedule Settings view area.

SB Low and SB High are displayed only when the optional setback function is enabled.

(7)

button

Saves the edit and closes the screen.

(8)

Cancel

button

Cancels the edit and closes the screen. Touching the button displays a confirmation dialog.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды