Daikin DCM601A51 Скачать руководство пользователя страница 112

Страница: 112 / 344

User’s Manual EM11A015B

intelligent Touch Manager

111

• When

Representative suction temperature – Representative setpoint (Heat) > Thermal diff 1.5

operation mode is changed from Heat to Cool
• When

Representative setpoint (Cool) – Representative suction temperature > Thermal diff 1.5

operation mode is changed from Cool to Heat

°C

Representative setpoint (Heat) +
Thermal difference in (0°C) + 1.

Representative
suction
temperature

°C

<When the thermal difference is 0°C>

Representative setpoint (Cool/Heat)

1.5°C

Representative setpoint (Cool) –
Thermal difference in (0°C) – 1.

When the thermal difference is 0°C

Heating mode Cooling mode

Cooling mode Heating mode

Heating mode

Cooling mode

The following describes how to create and set up an Auto Changeover group.

Creating and editing an Auto Changeover group

1. Touch the Auto Changeover button on the Automatic Ctrl. tab of the Menu List screen and

display the Automatic Changeover settings screen (see “4-5 Menu List Screen: Automatic Ctrl.

Tab”).

(1)

(2)
(3)
(4)

(1)

is a list of registered Auto Changeover groups. To create a new group, touch the

Create

button

(2)

and enter the group name in the Name Setup dialog that appears. Duplicate names

are not permitted. You can create up to 512 groups.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды