Daikin DCM601A51 Скачать руководство пользователя страница 135

Страница: 135 / 344

User’s Manual EM11A015B

intelligent Touch Manager

134

6-4 Setting up Maintenance and Checking

You can set a specific management point to “maintenance” or release it from “maintenance”.

A management point set to “maintenance” cannot be controlled from the iTM, that is, it cannot

receive input signals such as orders of operation, automatic control, status monitoring, etc.

However, emergency stop is possible.

The following describes how to set this function up.

Touch the Maintenance button on the System Settings tab of the Menu List screen and display

the Maintenance Settings screen (see “4-5 Menu List Screen: System Settings Tab”).

(2)

(1)

To set to maintenance, select it from the list of Available Management Points displayed in

(1)

and touch the Add button to move it to

(2)

. The management point is set to maintenance. Touch

the OK button to close the screen.

To release from maintenance, select a points under maintenance from

(2)

and touch the

Remove button to move it to

(1)

. The management point is released from maintenance.

When finished, touch the OK button to close the screen.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды