Daikin DCM601A51 Скачать руководство пользователя страница 203

Страница: 203 / 344

User’s Manual EM11A015B

intelligent Touch Manager

202

The following describes how to set this up.

Touch the Sliding Temp. button on the Automatic Ctrl. tab of the Menu List screen and display

the Sliding Temperature Settings screen (see “4-5 Menu List screen: Automatic Ctrl. Tab”).

(1)

(2)
(3)
(4)
(5)

(1)

is the list of Sliding Temperature groups. Perform the intended operation by touching the

relevant button on the right.

(2)

Create

button

Creates a new group and displays the Name Setup dialog that allows you to enter the name.

Duplicate names are not permitted. You can create up to 8 Sliding Temperature groups. Touch

the OK button and close the screen. The created group is added to the list.

(3)

Delete

button

Deletes the selected group.

(4)

Registration

button

Displays the Registration screen that allows you to register/delete group members.

(5)

Attributes

button

Displays the Attribute screen that allows you to rename the selected group, set up the upper

limit/lower limit outdoor temperatures and/or setpoints, etc.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды