Daikin DCM601A51 Скачать руководство пользователя страница 202

Страница: 202 / 344

User’s Manual EM11A015B

intelligent Touch Manager

201

8-5

Setting up the Sliding Temperature

Sliding Temperature is a function that changes the indoor unit setpoint in accordance with the

changes in the outdoor temperature so that the difference between the outdoor and indoor

temperatures is not excessive in rooms with direct access to/from outside the building. This function

works only when the indoor unit is working in Cool mode.

The setpoint of an indoor unit registered with a Sliding Temperature group you have created and

have this function enabled may change every 5 minutes depending on the outdoor temperature

measured at the Ai management point.

The outdoor temperature and setpoint are linked through the following expressions:

• When the outdoor temperature is higher than the upper limit outdoor temperature

Setpoint = Upper limit setpoint

• When the outdoor temperature is lower than the lower limit outdoor temperature

Setpoint = Lower limit setpoint

• When the outdoor temperature is within the range specified by the upper and limits of the outdoor

temperature

Setpoint = (Outdoor temperature – Lower limit outdoor temperature) × (Upper limit setpoint –

Lower limit setpoint) / (Upper limit outdoor temperature – Lower limit outdoor temperature) +

Lower limit setpoint

• The value of the calculated setpoint is round off.

NOTE

Setpoint

Outdoor
temperature

Lower limit outdoor
temperature

Lower limit setpoint

Upper limit setpoint

Relationship between Outdoor Temperature and Setpoint

Setpoint

Upper limit outdoor
temperature

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды