Daikin DCM601A51 Скачать руководство пользователя страница 208

Страница: 208 / 344

User’s Manual EM11A015B

intelligent Touch Manager

207

8-6 Setting up the Heating Mode Optimization

Heating Mode Optimization is a function that stops the indoor unit while its operating status

indication is kept unchanged to prevent unnecessary temperature rise and the feelings of

discomfort during heating.

This function performs the following every 5 minutes for each indoor unit with this function enabled.

• When heating and suction temperature > se1°C, stops the indoor unit. However, the iTM

display will continue to indicate On. (Display of the remote controller will indicate Off.)

• While stopped by this function, if suction temperature < setpoint –1°C, starts the indoor unit.

• While stopped by this function, if Heating Mode Optimization is changed from “Enabled” to

“Disabled” in the Heating Mode Optimization Settings screen, starts the indoor unit.

• While stopped by this function, if the operation mode is changed to other than heating, starts the

indoor unit.

If suction temperature could not be acquired from an indoor unit controlled by this function, the

above described assessment is not performed. The operational status at that point is kept and the

attempt to acquire the suction temperature continues every 5 minutes until it succeeds.

Temperature

Time

Setpoint –1°C

Setpoint

Room Temperature and Setpoint at Indoor Unit

and Heat Interruption Control

Se 1°C

Temperature
change

Resumption of fan

Interruption control

Fan OFF

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды