Midea MSH-18HRIN1 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 15

background image

(Inverter Split Type)

Please read this installation manual completely

before installing the product.

When the power cord is damaged, replacement

work shall be performed by authorized personnel
only.

Installation work must be performed in accordance

with the national wiring standards by authorized
personnel only.

Contact the authorised service technician for

repair or maintenance of this unit.

ROOM AIR CONDITIONER

INSTALLATION MANUAL

1
2
3
...
»

Содержание MSH-18HRIN1
















Отзывы:

Нет отзывов

Похожие инструкции для MSH-18HRIN1

Бренд: Samsung Страницы: 35

AC TN4PKG Series

Бренд: Samsung Страницы: 20

AERAMAX PRO AM3 PC

Бренд: Fellowes Страницы: 8

SUNLINE MAGNUM DJ 180

Бренд: York Страницы: 40

VRV FXZQ07MVJU9

Бренд: Daikin Страницы: 27

Бренд: Bionaire Страницы: 2

MDV DCTB-24R32IVT IN

Бренд: aircon Страницы: 84

WMMS-09C-V2A/B(58) 2

Бренд: YMGI Страницы: 20

Бренд: Sakura Страницы: 20

Бренд: Daikin Страницы: 84

Бренд: Filtrete Страницы: 40

T?CLASS TPA024S4

Бренд: Lennox Страницы: 32

Бренд: Goodman Страницы: 48

Бренд: Daikin Страницы: 23

Бренд: Convair Страницы: 16

smart clima GABBIA GA - 700

Бренд: Tecnosystemi Страницы: 4

Бренд: Samsung Страницы: 46

AR-KP/JP Series

Бренд: Samsung Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды