manualshive.com logo in svg

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Серия продуктов Cisco uBR7200 – это мощные маршрутизаторы, обеспечивающие быструю и надежную связь. Вы сможете настроить устройство с помощью бесплатного руководства по настройке программного обеспечения, которое доступно для скачивания на {веб-сайте}. Управляйте своей сетью легко и эффективно!

Поделиться
Скачать
background image

2-25

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 2      Configuring the Cable Modem Termination System for the First Time

Configuring the Cable Interface with the Extended Setup Facility

IP address for the DHCP server [X.X.X.X]: 10.0.0.2
Configure IP on this interface? [yes]:
IP address for this interface [10.20.133.65]:
Subnet mask for this interface [255.0.0.0]: 255.255.255.248
Class A network is 10.0.0.0, 29 subnet bits; mask is /29
In this example, the input above generates the following command interface script:
interface Cable 5/0
no shutdown
cable downstream frequency 531000000
no shutdown
cable downstream modulation 64qam
cable downstream annex B
cable downstream interleave-depth 32
no cable upstream 0 shutdown
cable upstream 0 frequency 33808000
cable helper-address 10.0.0.2
ip address 10.20.133.65 255.255.255.248

Note

Cable modems or set-top boxes with integrated cable modems are brought online when the utility is run.  

Note

For Dynamic Host Configuration Protocol (DHCP)/time of day (TOD)/Trivial File Transfer Protocol 
(TFTP), a static route must exist to the host.  

Configuring the Cable Interface with the Extended Setup Facility

The Setup facility creates an initial configuration. The basic management setup configures only enough 
connectivity for management of the system. The Extended setup facility prompts you to configure each 
interface on the system. 

To invoke the configuration facility, use the following command:

Router# 

setup

The following is the System Configuration dialog:

Continue with configuration dialog? [yes/no]: yes

Identifying the Cable Interface Line Card

Identifying Cable Modem Line Cards

The following Cisco cable interfaces can be installed in a Cisco CMTS:

  •

The Cisco uBR7200 series router supports one downstream modulator and one upstream 
demodulator. 

  –

The Cisco uBR7200 series router supports the following defaults: QAM-256 at 40 MBps 
downstream, and QAM-16 at 5 Mbps upstream. 

  –

The card supports upstream channel widths of 200 kHz, 400 kHz, 800 kHz, 1.6 MHz, and 
3.2 MHz. 

  –

The card o42 dBmV and +/- 2 dBmV. 

  –

The downstream modulator has both an RF output, using the integrated upconverter, and an 
intermediate frequency (IF) output, which must be connected to an external upconverter. 

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

D-Link ShareCenter Quattro DNS-345 Quick Install Manual preview
ShareCenter Quattro DNS-345
Бренд: D-Link Страницы: 40
D-Link ShareCenter Quattro DNS-345 Datasheet preview
ShareCenter Quattro DNS-345
Бренд: D-Link Страницы: 4
D-Link AirPlus G DWL-G710 Troubleshooting preview
AirPlus G DWL-G710
Бренд: D-Link Страницы: 5
D-Link MYDLINK DNR-322L Datasheet preview
MYDLINK DNR-322L
Бренд: D-Link Страницы: 4
D-Link mydlink DNR-312L Quick Install Manual preview
mydlink DNR-312L
Бренд: D-Link Страницы: 8
D-Link AC750 Quick Install Manual preview
AC750
Бренд: D-Link Страницы: 12
D-Link DNS-722-4 Quick Install Manual preview
DNS-722-4
Бренд: D-Link Страницы: 16
D-Link DNS-722-4 User Manual preview
DNS-722-4
Бренд: D-Link Страницы: 88
IBM 11a Quick Start Manual preview
11a
Бренд: IBM Страницы: 32
Oracle Talari E1000 Installation Manual preview
Talari E1000
Бренд: Oracle Страницы: 24
Maxim MAX1415 Specification Sheet preview
MAX1415
Бренд: Maxim Страницы: 14
Patton electronics 1000RC User Manual preview
1000RC
Бренд: Patton electronics Страницы: 9
Qlogic QLE7xxx Series Quick Start Manual preview
QLE7xxx Series
Бренд: Qlogic Страницы: 8
ZALMAN ZM-RF1 User Manual preview
ZM-RF1
Бренд: ZALMAN Страницы: 5
4gon RouterBOARD 411R Quick Start Manual preview
RouterBOARD 411R
Бренд: 4gon Страницы: 2
Gira 0535 00 Installation Instructions Manual preview
0535 00
Бренд: Gira Страницы: 6
Softing CAN-PRO1-PCIE Hardware User Manual preview
CAN-PRO1-PCIE
Бренд: Softing Страницы: 4
Xenya XS26GS User Manual preview
XS26GS
Бренд: Xenya Страницы: 189

Бренды по названию

Популярные бренды

Загрузить еще бренды