manualshive.com logo in svg

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Серия продуктов Cisco uBR7200 – это мощные маршрутизаторы, обеспечивающие быструю и надежную связь. Вы сможете настроить устройство с помощью бесплатного руководства по настройке программного обеспечения, которое доступно для скачивания на {веб-сайте}. Управляйте своей сетью легко и эффективно!

Поделиться
Скачать
background image

A-3

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Appendix A      Installing or Upgrading Cisco IOS Software

Installing or Upgrading Cisco IOS Software

Step 6

Specify the destination filename: 

Destination file name? 

ubr7200-k8p-mz

This is the name the new software image will have when it is loaded onto the router. The image can be 
named anything, but common practice is to enter the UNIX image filename. 

Step 7

Erase the Flash device before confirming: 

a.

Enter 

yes

 to erase the existing software image resident in the router's Flash memory before copying 

the new one. 

b.

Enter 

no

 to keep the existing software image. Be sure that you have enough Flash memory to keep both. 

Erase flash device before writing? [confirm] yes/no 

The copying process requires several minutes; the time differs from network to network. During the 
copying process, messages are displayed to indicate which files have been accessed. 

The exclamation point "!" indicates that the copying process is taking place. Each exclamation point 
indicates that ten packets have been transferred successfully. A checksum verification of the image 
occurs after the image is written to Flash memory. 

Step 8

Before reloading, verify the correct installation and commands. 

a.

Verify that the image is properly installed and that the boot system commands point to the proper 
file to load. Information about verifying the image and boot commands is available in 

Appendix B, 

“Resolving Common Image Installation Problems.”

 

b.

To reload the image, type: 

Router# 

reload

*Mar 1 00:30:49.972: %SYS-5-CONFIG_I: Configured from console by console

System configuration has been modified. Save? [yes/no]: no !-- lower case

Proceed with reload? [confirm] yes !-- lower case

Step 9

Use the 

show version 

command to verify that the router is running with the proper image. 

Sample Output—Cisco uBR7200 Series Router

Router# 

show flash

-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name

1   .. unknown  317FBA1B  4A0694   24  4720148 Aug 29 1997 17:49:36 

hampton/nitro/c7200-j-mz

2   .. unknown  9237F3FF  92C574   11  4767328 Oct 01 1997 18:42:53 c7200-js-mz

3   .D unknown  71AB01F1 10C94E0   10  7982828 Oct 01 1997 18:48:14 rsp-jsv-mz

4   .D unknown  96DACD45 10C97E0    8      639 Oct 02 1997 12:09:17 the_time

5   .. unknown  96DACD45 10C9AE0    3      639 Oct 02 1997 12:09:32 the_time

6   .D unknown  96DACD45 10C9DE0    8      639 Oct 02 1997 12:37:01 the_time

7   .. unknown  96DACD45 10CA0E0    8      639 Oct 02 1997 12:37:13 the_time

 

3104544 bytes available (17473760 bytes used)

Related Information 

The following documents on Cisco.com contain additional information related to software installation 
and upgrade:

  •

How to Choose a Cisco IOS Software Release

 

  •

Field Notice: Cisco IOS TFTP Client Cannot Transfer Files Larger than 16MB in Size

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

GE D20MX User Manual preview
D20MX
Бренд: GE Страницы: 146
Patton electronics 2888 Getting Started Manual preview
2888
Бренд: Patton electronics Страницы: 51
NETGEAR DG834GT - 108 Mbps Super G Wireless ADSL Router Specifications preview
DG834GT - 108 Mbps Super G Wireless ADSL Router
Бренд: NETGEAR Страницы: 2
FONESTAR XO-324 Instruction Manual preview
XO-324
Бренд: FONESTAR Страницы: 8
Maipu SM3100-28TC-AC Install Manual preview
SM3100-28TC-AC
Бренд: Maipu Страницы: 19
3Com FEM656C Quick Start Manual preview
FEM656C
Бренд: 3Com Страницы: 53
iNetVu Tachyon CI1300 Quick Start Manual preview
Tachyon CI1300
Бренд: iNetVu Страницы: 20
Meinberg CPU-C15G2 Setup Manual preview
CPU-C15G2
Бренд: Meinberg Страницы: 14
Smacq Technologies PCI-1232 User Manual preview
PCI-1232
Бренд: Smacq Technologies Страницы: 22
Uctronics U6180 Instruction Manual preview
U6180
Бренд: Uctronics Страницы: 2
Neousys Technology PCIe-PoE334LP User Manual preview
PCIe-PoE334LP
Бренд: Neousys Technology Страницы: 39
Hama 49276 Operating Instruction preview
49276
Бренд: Hama Страницы: 7
Dantel 44118 Installation & Operation Manual preview
44118
Бренд: Dantel Страницы: 22
Pro-Nets Technology Corporation WR750RL User Manual preview
WR750RL
Бренд: Pro-Nets Technology Corporation Страницы: 48
Gbord EN-203 User Manual preview
EN-203
Бренд: Gbord Страницы: 11
Patton electronics IpLink 2884 Quick Start Manual preview
IpLink 2884
Бренд: Patton electronics Страницы: 8
Terasic Cypress CapSense P0080 User Manual preview
Cypress CapSense P0080
Бренд: Terasic Страницы: 22
H3C SecPath L5030 Installation Manual preview
SecPath L5030
Бренд: H3C Страницы: 62

Бренды по названию

Популярные бренды

Загрузить еще бренды