manualshive.com logo in svg

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Серия продуктов Cisco uBR7200 – это мощные маршрутизаторы, обеспечивающие быструю и надежную связь. Вы сможете настроить устройство с помощью бесплатного руководства по настройке программного обеспечения, которое доступно для скачивания на {веб-сайте}. Управляйте своей сетью легко и эффективно!

Поделиться
Скачать
background image

3-27

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 3      Configuring Cable Modem Interface Features

Configuring the Upstream Cable Modem Interface

Router# 

show interface c5/0 sid 1 counters

00:02:23: %ENVM-3-LASTENV: Cannot save environmental data 

Sid  Req-polls  BW-reqs    Grants     Packets    Frag       Concatpkts

     issued     received   issued     received   complete   received

1    0          22         22         22         0          0          

2    0          3          3          2          0          0          

3    0          0          0          0          0          0 

Verifying Upstream Traffic Shaping

To determine if upstream traffic shaping is configured and activated, enter the

 show running-config

 

command and look for the cable interface configuration information. If upstream traffic shaping is 
configured and enabled, a traffic shaping entry appears in the 

show running-config 

output. If upstream 

traffic shaping is disabled,

 

no cable upstream rate-limit 

appears in the output.

You can also perform the following tasks to verify that traffic shaping is enabled on the upstream channel:

Step 1

Configure a low-peak upstream rate limit for the CM in its QoS profile. Either use the command-line 
interface (CLI) to modify the modem’s QoS profile, or edit the modem’s TFTP configuration file. refer 
to the

DOCSIS 1.1 for the Cisco uBR7200 Series Universal Broadband Routers

 feature module on 

Cisco.com. 

Step 2

Use a regular rate-limiting algorithm on the upstream without rate shaping, and note the drops of the 
excess bandwidth requests from this CM when it exceeds its peak upstream rate. 

Use the 

show interface c

x

/

y

 sid counters verbose 

command to see the bandwidth request drops.

 

Verify 

that the upstream rate received by that modem is less than its configured peak rate, due to the timeouts 
and backoffs produced by the drop in bandwidth requests. Enter the 

show interface c

x/y

 service flow qos 

command to see the input rate at CMTS in bps.

Step 3

Enable grant shaping on the upstream channel by using the new 

shaping

 keyword extension to the 

token-bucket algorithm CLI command.

Step 4

Make the CM exceed its peak upstream rate by generating upstream traffic, and note the effect of grant 
buffering (shaping) at the CMTS. If you use CM-to-CMTS pings, there is a perceivable decrease in the 
frequency of the pings. 

Let the pings run long enough to allow the averages at the CMTS to settle; then view the upstream rate 
received by this single modem. Use the 

show interface c

x

/

y

 command and see the input rate in bps. This 

value should be close to the modem’s peak upstream rate. Also note the drop counts for the modem’s 
SID by using the 

show interface sid counters 

command, and verify that the CMTS no longer drops the 

bandwidth requests from the CM.

The bandwidth request drop count (from the previous nonshaping test) remains unchanged when 
upstream rate shaping is used, indicating that the CMTS is actually shaping (buffering) the grants for the 
modem. Verify that the input rate at the CMTS (from the single rate-exceeded CM) stabilizes close to 
the configured peak rate of 128 Kbps.

Troubleshooting Tips

Perform these steps if you are having difficulty with verification:

Step 1

Ensure that the cable connections are not loose or disconnected.

Step 2

Ensure that the cable interface line card is firmly seated in its chassis slot.

Step 3

Ensure that the captive installation screws are tight.

Step 4

Verify that you have entered the correct slot and port numbers.

Step 5

Verify that you selected a valid frequency for your router.

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

CAME Z Series Manual preview
Z Series
Бренд: CAME Страницы: 4
Aaeon UP Squared 6000 Edge Computing Kit User Manual preview
UP Squared 6000 Edge Computing Kit
Бренд: Aaeon Страницы: 59
Acconeer A111 User Manual preview
A111
Бренд: Acconeer Страницы: 32
ICP DAS USA I-7532M-FD User Manual preview
I-7532M-FD
Бренд: ICP DAS USA Страницы: 48
ICP DAS USA WF-2572 User Manual preview
WF-2572
Бренд: ICP DAS USA Страницы: 24
ICP DAS USA MSM-508 Quick Start preview
MSM-508
Бренд: ICP DAS USA Страницы: 4
National Instruments NI 9426 Getting Started Manual preview
NI 9426
Бренд: National Instruments Страницы: 17
National Instruments NI PCIe-8255R Quick Start Manual preview
NI PCIe-8255R
Бренд: National Instruments Страницы: 16
National Instruments NI 9403 Operating Instructions Manual preview
NI 9403
Бренд: National Instruments Страницы: 23
Quatech DS-3000 User Manual preview
DS-3000
Бренд: Quatech Страницы: 27
Quantum Scalar 50 Upgrade Instructions preview
Scalar 50
Бренд: Quantum Страницы: 20
Salus PL07 Instruction Manual preview
PL07
Бренд: Salus Страницы: 16
Datasat AP25 Installation And Operating Manual preview
AP25
Бренд: Datasat Страницы: 170
D-Link G416 User Manual preview
G416
Бренд: D-Link Страницы: 176
D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Manual preview
AirPlus XtremeG Ethernet-to-Wireless Bridge...
Бренд: D-Link Страницы: 31
Industrex M43ic Instruction Manual preview
M43ic
Бренд: Industrex Страницы: 51
Fostex DE-1 Service Manual preview
DE-1
Бренд: Fostex Страницы: 20
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Бренд: Dialogic Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды