manualshive.com logo in svg

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Серия продуктов Cisco uBR7200 – это мощные маршрутизаторы, обеспечивающие быструю и надежную связь. Вы сможете настроить устройство с помощью бесплатного руководства по настройке программного обеспечения, которое доступно для скачивания на {веб-сайте}. Управляйте своей сетью легко и эффективно!

Поделиться
Скачать
background image

3-21

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 3      Configuring Cable Modem Interface Features

Configuring the Upstream Cable Modem Interface

  Minislot Size in number of Timebase Ticks is = 8

  Minislot Size in Symbols = 64

  Bandwidth Requests = 0xFE

  Piggyback Requests = 0xD

  Invalid BW Requests= 0x2

  Minislots Requested= 0x2963

  Minislots Granted  = 0x2963

  Minislot Size in Bytes = 16

  Map Advance = 4000 usecs

  UCD Count = 32964

  DES Ctrl Reg#0 = C000C043, Reg#1 = 0

Setting the Upstream Channel Width

Use the commands below to enter the upstream channel width in hertz (Hz). For NTSC operations, valid 
values are 200000 Hz (160 kilo symbols per second [ksps]), 400,000 Hz (320 ksps), 800,000 Hz 
(640 ksps), 1,600,000 Hz (1280 ksps), and 3,200,000 Hz (2560 ksps). The default is 1,600,000 Hz. 

If no acceptable channels of the specified width are found, the spectrum management card automatically 
begins to scan the upstream spectrum for the next largest available channel width; for example, if the 
spectrum management card is unable to find a usable 1.6 MHz upstream channel, it automatically begins 
searching for usable 800 kHz channels. 

Caution

Higher symbol rates are more susceptible to RF noise and interference. If you use a symbol rate or 
modulation format beyond the capabilities of your HFC network, you might experience packet loss or 
loss of cable interface connectivity.

Note

For QAM-16 channel widths of 400 kHz (320 ksps) or greater, Cisco recommends that you use QAM-16 
modulation for long and short data, and that you use QPSK for request, initial, and station 
communications. For QAM-16 channel widths of 200 kHz (160 ksps), all communication must be able 
to use QAM-16. That is, 160 ksps with QAM-16 requires an exceptional signal-to-noise ratio (SNR) in 
your upstream channels. When you use QAM-16 for request, initial, and station maintenance messages 
with channel widths greater than 400 kHz, the QAM-16 preamble and message data take longer to 
transmit than the QPSK format. 

Note

To set the upstream channel width, use the following commands in cable interface configuration mode.

For additional information about channel width and minislot size, refer to the 

Cable Radio Frequency 

(RF) FAQs

 on Cisco.com. 

Verifying Upstream Channel Width

To verify the current value of the upstream channel width, enter the 

show controllers cable 

command 

for the upstream port you just configured. A sample follows below:

Router# 

show controllers cable5/0 u0

Cable5/0 Upstream 0 is up

  Frequency 24.016 MHz, Channel Width 0.800 MHz, QPSK Symbol Rate 0.640 Msps

Command

Purpose

Step 1

Router(config-if)# 

cable upstream 

usport

 

channel-width 

width

Enters the channel width for your upstream RF carrier in Hz.

Step 2

Router(config-if)# 

no cable upstream 

usport

 

channel-width

Returns the channel width to its default setting of 1,600,000 Hz.

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

ABB RELION REF615R Manual preview
RELION REF615R
Бренд: ABB Страницы: 66
Maco Standard Fitting Instructions Manual preview
Standard
Бренд: Maco Страницы: 38
EAW MX250 Owner'S Manual preview
MX250
Бренд: EAW Страницы: 10
EAW MX8000 Technical Specifications preview
MX8000
Бренд: EAW Страницы: 2
B&B Electronics Elinx EIRP305-T User Manual preview
Elinx EIRP305-T
Бренд: B&B Electronics Страницы: 19
IBM LS42 - BladeCenter - 7902 Installation Manual preview
LS42 - BladeCenter - 7902
Бренд: IBM Страницы: 56
IBM ATA 133 Quick Hardware Setup Manual preview
ATA 133
Бренд: IBM Страницы: 2
IBM BladeCenter Management Module User Manual preview
BladeCenter Management Module
Бренд: IBM Страницы: 78
IBM 9040-MR9 Manual preview
9040-MR9
Бренд: IBM Страницы: 110
IBM Remote Supervisor Adapter II User Manual preview
Remote Supervisor Adapter II
Бренд: IBM Страницы: 132
Paradyne Hotwire 5446 Notice preview
Hotwire 5446
Бренд: Paradyne Страницы: 2
Paradyne Hotwire 6381 Installation Instructions Manual preview
Hotwire 6381
Бренд: Paradyne Страницы: 20
Paradyne Hotwire 6381 Upgrade Instructions preview
Hotwire 6381
Бренд: Paradyne Страницы: 2
Zhone Hotwire 6381 Quick Installation Instructions preview
Hotwire 6381
Бренд: Zhone Страницы: 2
PairGain PG-FLEX RT FRL-752 Manual preview
PG-FLEX RT FRL-752
Бренд: PairGain Страницы: 6
I-O Wireless WBC11 User Manual preview
WBC11
Бренд: I-O Wireless Страницы: 55
8level IPG-200 User Manual preview
IPG-200
Бренд: 8level Страницы: 52
Seriallink SLK-R602 Series Manual preview
SLK-R602 Series
Бренд: Seriallink Страницы: 29

Бренды по названию

Популярные бренды

Загрузить еще бренды