Cisco uBR7200 Series Скачать руководство пользователя страница 238 | Manualshive

Страница: 238 / 324

background image

5-8

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 5 Managing Cable Modems on the Hybrid Fiber-Coaxial Network

Configuring Maximum Hosts Attached to a Cable Modem

Configuring Maximum Hosts Attached to a Cable Modem

To specify the maximum number of hosts that can be attached to a subscriber’s CM, use the following
command in cable interface configuration mode.

Configuring Per-Modem Filters

You can configure the Cisco uBR7200 series to filter incoming packets from individual hosts or
cable interfaces based on the source Media Access Controller (MAC) or Internet Protocol (IP) address.
Definition of filters follows standard Cisco IOS configuration practices for access lists and groups.

Note

Configuring per modem or host filters is supported in Cisco IOS Release 12.0(5)T1 or higher, as well as
in Cisco IOS Release 12.0(6)SC or higher.

To specify the access group (per-modem filter), use the

cable modem access-group

command in privileged

EXEC mode. To disable the specification, use the

no access-group

form of this command.

cable modem

{

mac-addr

|

ip-addr

}

access-group

[

access-list

|

access-name

]

cable modem

{

mac-addr

|

ip-addr

}

no access-group

Syntax Description

Examples

The following example shows the

cable modem access-group

command assigning access-list 1 to the

CM with the MAC address of abcd.ef01.2345:

Router# cable modem abcd.ef01.2345 access-group 1

This command configures access lists to be specified on a per-interface and per-direction basis. The
packets received from cable interfaces and/or individual hosts are filtered based on the cable interface
or the host the packets are received from. Use

modem

if the device is a CM. Use

host

if the device is a

CPE device attached to a CM.

The

macaddr

specifies the CM’s or CPE device’s unique MAC address. Define the filter to be applied to

the device and a given address.

Use the

ipaddr

option to specify the CM or CPE device’s current IP address.

Command

Purpose

cable max-hosts

n

no cable max-hosts

Specifies the maximum number of hosts that can be attached to a CM on
this interface. Valid range is from 0 to 255 hosts. Default = 0.

Resets the allowable number of hosts attached to a CM to the default value
of 0 hosts.

ip-addr

Specifies the IP address for the CM.

mac-address

Specifies the MAC address for the CM.

access-list

Specifies the IP access list (standard or extended). Valid values are 1 to 199.

access-name

Specifies the access-list name.

«
...
236
237
238
239
240
...
»

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

Бренд: N.A.T. Страницы: 32

Бренд: Belkin Страницы: 2

NetVanta Serial Dial Backup Interface Module (DIM) none

Бренд: ADTRAN Страницы: 2

Бренд: uneron Страницы: 13

8-Port 10/100Mbps Fast Ethernet Switch

Бренд: Amer.com Страницы: 14

Бренд: Zonet Страницы: 1

Бренд: Kordis Страницы: 31

Бренд: Paradyne Страницы: 28

SCREENSHARE PRO

Бренд: V7 Страницы: 4

Бренд: ADTRAN Страницы: 4

Бренд: Lantech Страницы: 20

Бренд: National Instruments Страницы: 37

Бренд: Motorola Страницы: 376

Бренд: Motorola Страницы: 20

Бренд: MikroTik Страницы: 7

RouterBOARD 493

Бренд: 4gon Страницы: 2

Бренд: Zte Страницы: 38

Бренд: Panasonic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды