Cisco uBR7200 Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 324

background image

1-11

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-05

Chapter 1 Overview of Cisco uBR7200 Series Software

Cisco uBR7200 Series Chassis Overview

Supported Hardware on the Cisco uBR7200 Series

Table 1-5

provides a quick overview of the major hardware features of the Cisco uBR7200 series routers.

Note

Earlier release notes stated that the NPE-175 was also supported on the Cisco uBR7200 series routers.
Because the NPE-175 has reached its end of life and was never made available for order on the Cisco
uBR7200 series routers, it has been removed from the table.

The UBR7200-NPE-G1 does not require that an I/O controller be installed. Refer to the

Cisco uBR7200

Series Software Release Notes

on Cisco.com:

http://www.cisco.com/en/US/docs/cable/cmts/ubr7200/release/notes/12_3bc/123BCu72.html

Network Processing Engines

The Cisco uBR7246 VXR supports the following Network Processing Engines (NPEs):

•

UBR7200-NPE-G1

•

NPE-225

•

NPE-300

•

NPE-400

The Cisco uBR7223 and the Cisco uBR7246 support the following Network Processing Engines (NPE) :

•

NPE-150

•

NPE-200

•

NPE-225

Note

The NPE-300 and NPE-400 are not supported on the Cisco uBR7223 and the Cisco uBR7246. The
NPE-150 and NPE-200 are not supported on the Cisco uBR7246 VXR.

Table 1-5

Cisco uBR7200 Series Hardware Overview

Supported Hardware

Cisco uBR7246 VXR

Cisco uBR7246

Cisco uBR7223

Network Processing Engines

One of the following:

•

UBR7200-NPE-G1

•

NPE-225

•

NPE-300

•

NPE-400

One of the following:

•

NPE-150

•

NPE-200

•

NPE-225

One of the following:

•

NPE-150

•

NPE-200

•

NPE-225

I/O Controllers

One of the following:

•

UBR7200-I/O

•

UBR7200-I/O-FE

•

UBR7200-I/O-2FE/E

One of the following:

•

UBR7200-I/O

•

UBR7200-I/O-FE

One of the following:

•

UBR7200-I/O

•

UBR7200-I/O-FE

Network Interface Port Adapters

Up to two

Up to two

One

Cable Interface Line Cards

Up to four

Up to four

Up to four

Removable Power Supplies

Up to two

Up to two

One

PCMCIA Slots

Two

Two

Two

«
...
27
28
29
30
31
...
»

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

Бренд: Watchguard Страницы: 40

NetDefend DFL-260E

Бренд: D-Link Страницы: 328

ShareCenter Pulse DNS-320

Бренд: D-Link Страницы: 2

DFL-210 - NetDefend - Security Appliance

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 22

Бренд: D-Link Страницы: 4

Бренд: Dahua Страницы: 12

NetDefend DFL-1600

Бренд: D-Link Страницы: 23

Бренд: Linksys Страницы: 2

Бренд: Qualys Страницы: 2

Бренд: Observint Страницы: 117

Бренд: Harmonic Страницы: 56

HomePlug AV Ethernet Bridge PLE0200

Бренд: Abocom Страницы: 2

Бренд: Rosewill Страницы: 3

WGR614 - Wireless-G Router Wireless

Бренд: NETGEAR Страницы: 116

Бренд: M86 Security Страницы: 309

Storage Networking (Unified Fabric Pilot)

Бренд: Qlogic Страницы: 76

Бренд: Conel Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды