Cisco uBR7200 Series Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 324

background image

1-22

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-05

Chapter 1 Overview of Cisco uBR7200 Series Software

Supported Software Features for the Cisco uBR7200 Series

Supported Software Features for the Cisco uBR7200 Series

This section summarizes Cisco uBR7200 series router software features for all supported Cisco IOS
Release trains, and directs you to additional configuration information for each feature.

Cisco uBR7200 Series Router Features and Cisco IOS Releases

Table 1-9

summarizes the software-related features and related Cisco IOS releases that support the

Cisco uBR7200 series router. Cisco IOS features indicate the first release in which the feature was
introduced. Unless otherwise noted, feature support continues in later releases of the same or related
Cisco IOS release train

Many additional features were introduced in release trains prior to those listed above, such as 12.0 T,
12.0 SC, 12.1 XF and other earlier releases that may no longer be supported on the Cisco uBR7200
Series. Refer to the release notes for your respective Cisco IOS release for additional feature support and
image information.

Table 1-9

Cisco uBR7200 Series Routers Features by Cisco IOS Release

Feature

Supporting Cisco IOS Releases

Cisco uBR7200 Series Router Configuration Tools

Autoinstall

12.0 T, 12.0 XR, 12.0 SC, 12.1 EC, 12.1 CX, 12.2 BC and 12.3
BC releases

Cable Interface Setup Facility

12.1 EC, 12.1 CX, 12.2 BC and 12.3 BC releases

Cable Interface Extended Setup
Facility

12.1(3a)EC1 and all later Cisco IOS releases supporting the
Cisco uBR7200 Series CMTS

Cisco Network Registrar

12.1 EC, 12.2 BC, 12.3 BC

Interface Range Specification

12.0 T, 12.0 XR, 12.0 SC, 12.1 EC, 12.1 CX, 12.2 BC and 12.3
BC releases

Internal Modem Configuration File
Editor

12.2(1)XF1 and later 12.2 XF, 12.2 BC and 12.3 BC releases

Manual Configuration Mode for the
Cisco uBR7200 Series CMTS

All Cisco IOS releases supporting the Cisco uBR7200 Series
CMTS

Virtual Interface Support and
Frequency Stacking Support

12.3(9a)BC and later 12.3 BC releases

Bandwidth Management Features

Load Balancing Support

12.3(9a)BC and later 12.3 BC releases

Cisco IOS Command-Line Enhancements

exec prompt timestamp Command

12.1(12c)EC, 12.2(8)BC2 and later 12.1 EC, 12.2 BC and 12.3
BC releases

show Command Enhancements

Multiple Cisco IOS software releases. Enhancements include:

•

show cable qos

•

show int cx/y sid

•

show cable modem

•

show cable modulation-profile

•

show cable modem summary

«
...
38
39
40
41
42
...
»

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

Бренд: D-Link Страницы: 11

Бренд: D-Link Страницы: 8

AirPlus DWL-810

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 84

Elinx EIRP305-T

Бренд: B&B Electronics Страницы: 19

SmartMedia Adapter PC Card REX-SMA01F

Бренд: Ratoc Systems Страницы: 75

Бренд: XAVI Technologies Corp. Страницы: 71

Бренд: TFortis Страницы: 86

Linear SCP-LT8362-S-EVALZ

Бренд: Analog Devices Страницы: 8

Бренд: Renesas Страницы: 941

Бренд: WAGO Страницы: 2

Бренд: Supero Страницы: 53

Бренд: ZyXEL Communications Страницы: 8

Бренд: Intel Страницы: 578

Бренд: AES Страницы: 44

N-FXE 02B Series

Бренд: Lantronix Страницы: 10

Бренд: FiberHome Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды