Cisco uBR7200 Series Скачать руководство пользователя страница 183 | Manualshive

Страница: 183 / 324

background image

2-21

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 2 Configuring the Cable Modem Termination System for the First Time

Configuring the Cisco uBR7200 Series Using the Setup Facility

Is this interface in use? [yes]:
  Configure this interface? [yes]:
  IP address for this interface [19.2.22.6]:
  Number of bits in subnet field [8]:
  Class A network is 19.0.0.0, 8 subnet bits; mask is /16

The configuration program displays the newly created command interface script:

The following command script was created:

hostname router
enable secret 5 $1$f0fc$A38P/KN/9yD3sEKSt6hKQ/
enable password betty
line vty 0 4
password wilma
snmp-server community public
!
ip routing
!
interface cable 5/0
ip address 19.2.22.5 255.255.0.0

router igrp 15
network 19.0.0.0
!
end

Step 10

When asked if you want to use this configuration, enter

yes

or press

Return.

Use this configuration? [yes/no]:

yes

Step 11

Save the configuration to NVRAM:

Router#

copy running-config startup-config

Note

You must always manually save the configuration settings to NVRAM whenever they are modified.

Configuring Upstream Frequencies with the Setup Facility

Upstream parameters must be configured manually. After the

Setup facility

is run, upstream ports have

a default state of “shutdown.” You have two methods to configure upstream channel frequencies:

•

Configure a fixed frequency between 5 to 42 MHz for North American channel plans, and enable
the upstream port.

•

Create a global spectrum group, assign the interface to it, and enable the upstream port.

The cable interface card receiver accepts time-division multiplexed burst transmissions from
cable interfaces (or CMs in set-top boxes), which are DOCSIS-based. The upstream port becomes “up”
when it is assigned an upstream frequency and is configured to be administratively up.

The upstream port is frequency-agile. The frequency can change while the interface is up and carrying
traffic, if you define spectrum groups per the example provided.

Configuring Individual Upstream Modulation Profiles

You can define individual modulation profiles. A modulation profile consists of a table of physical layer
characteristics for the different types of upstream bursts such as initial maintenance, long grant, request
data, request, short grant, and station maintenance.

Note

Only qualified personnel should define upstream modulation profiles.

«
...
181
182
183
184
185
...
»

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 49

UniFi Cloud Key

Бренд: Ubiquiti Страницы: 13

Бренд: B&B Electronics Страницы: 2

Wireless Connectivity Cape

Бренд: Element14 Страницы: 2

PSoC 4 S Series

Бренд: Cypress Страницы: 4

Бренд: Accton Technology Страницы: 78

Бренд: Airlinkplus Страницы: 20

Бренд: PairGain Страницы: 80

TeleMyo 2400T V2

Бренд: Noraxon Страницы: 52

Бренд: Digital Equipment Страницы: 90

CNPS8900 Series

Бренд: ZALMAN Страницы: 10

Бренд: PACOM Страницы: 16

Бренд: H3C Страницы: 148

Бренд: Zte Страницы: 32

Бренд: Epson Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды