Cisco uBR7200 Series Скачать руководство пользователя страница 30

Страница: 30 / 324

1-12

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-05

Chapter 1 Overview of Cisco uBR7200 Series Software

Cisco uBR7200 Series Chassis Overview

For more information, refer to the following resources on Cisco.com:

•

Network Processing Engine and Network Services Engine Installation and Configuration Guide

•

Memory Replacement Instructions for the Network Processing Engine or Network Services Engine and
Input/Output Controller

I/O Controllers

The Cisco uBR7200 series universal broadband routers support the following input/output (I/O)
controllers:

•

UBR7200-I/O-2FE/E input/output controller

–

Features two Fast Ethernet ports and one Ethernet port.

–

Equipped with 2 RJ-45 receptacles for 10/100 Mbps operation.

–

Supported for the Cisco uBR7246VXR router.

–

The Cisco IOS Release 12.1(10)EC boot helper image [ubr7200-boot-mz.12.1-10.EC] must be
used on this controlle.r

•

UBR7200-I/O-FE

–

Features one Fast Ethernet port.

–

Equipped with an MII receptacle and an RJ-45 receptacle for use at 100 Mbps full-duplex or
half-duplex operation.

–

Only one receptacle can be configured for use at a time.

–

Supported for Cisco uBR7223, Cisco uBR7246, and Cisco uBR7246 VXR routers.

–

The 12.0(15)SC [ubr7200-boot-mz.12.0-15.SC] boot helper image is recommended for this
controller.

•

UBR7200-I/O

–

Has no Fast Ethernet port.

–

Supported for Cisco uBR7223, Cisco uBR7246, and Cisco uBR7246 VXR routers.

–

The 12.0(15)SC [ubr7200-boot-mz.12.0-15.SC] boot helper image is recommended for this
controller.

Note

The Single-Port Fast Ethernet I/O Controller (UBR7200-I/O-FE) reached its End of Sale (EOS) point
on June 30, 2003. For details, see the Addendum to Product Bulletin, No. 1725, available at the
following location on Cisco.com:

http://www.cisco.com/en/US/products/hw/cable/ps2217/prod_eol_notice09186a00800a470d.html

Note

Do not use the 12.1(10)EC boot helper image with the UBR7200-I/O-FE and UBR7200-I/O
controllers.

Содержание uBR7200 Series





































































































































































































































































































































Результаты поиска

Содержание uBR7200 Series

Отзывы:

Похожие инструкции для uBR7200 Series

Бренды по названию

Популярные бренды

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Результаты поиска

Содержание uBR7200 Series

Отзывы:

Похожие инструкции для uBR7200 Series

Бренды по названию

Популярные бренды