Cisco uBR7200 Series Скачать руководство пользователя страница 110

Страница: 110 / 324

1-92

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-05

Chapter 1 Overview of Cisco uBR7200 Series Software

cops tcp window-size

•

Support for SNMP versions (SNMPv1, SNMPv2c, and SNMPv3).

•

Notification of faults, alarms, and conditions that can affect services.

Additional Information

To access the

Cisco CMTS Universal Broadband Router MIB Specifications Guide

, go to:

http://www.cisco.com/en/US/docs/cable/cmts/mib/reference/guide/ubrmibv5.html

MAX-CPE Override for Cable Modems

The following cable-specific configuration command provides a way to override the MAX-CPE
parameter in the cable modem's DOCSIS configuration file:

[

]

cable modem max-cpe

> |

unlimited

]

When set to unlimited or if

is larger than the MAX-CPE value in the configuration file of a cable

modem, it overrides the configuration file value.

Note

The

cable max-hosts

and

cable modem max-hosts

commands can also be used to set this value for all

cable modems on a particular cable interface or for a particular cable modem.

For additional command information, refer to these documents on Cisco.com:

•

Cisco IOS CMTS Cable Command Reference Guide

http://www.cisco.com/en/US/docs/ios/cable/command/reference/cbl_book.html

•

“Maximum CPE or Host Parameters for the Cisco Cable Modem Termination System” chapter in
the

Cisco Cable Modem Termination System Feature Guide

http://www.cisco.com/en/US/docs/cable/cmts/feature/guide/ufg_Max.html

•

Using the max-cpe Command in the DOCSIS and CMTS

, TAC Document ID: 22177

http://www.cisco.com/en/US/tech/tk86/tk168/technologies_tech_note09186a00800a7609.shtml

Per-Modem Error Counter Enhancements

The Cisco uBR7200 Series supports display of per-modem error counters with the following new command:

show cable modem

ip-addr

> | <

mac-addr

error

Below is an example display from the

show cable modem error

command:

Router#

show cable modem error

MAC Address SID I/F CRC HCS
00d0.ba26.eee7 1 Cable4/0/U0 0 0

Note

Both the Cyclic Redundancy Check (CRC) and Header Check Sum (HCS) are on a per- cable modem basis.

For additional command information about the

show cable modem

command, refer to the

Cisco IOS

CMTS Cable Command Reference Guide

on Cisco.com.

Содержание uBR7200 Series





































































































































































































































































































































Результаты поиска

Содержание uBR7200 Series

Отзывы:

Похожие инструкции для uBR7200 Series

Бренды по названию

Популярные бренды

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Результаты поиска

Содержание uBR7200 Series

Отзывы:

Похожие инструкции для uBR7200 Series

Бренды по названию

Популярные бренды