manualshive.com logo in svg

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Серия продуктов Cisco uBR7200 – это мощные маршрутизаторы, обеспечивающие быструю и надежную связь. Вы сможете настроить устройство с помощью бесплатного руководства по настройке программного обеспечения, которое доступно для скачивания на {веб-сайте}. Управляйте своей сетью легко и эффективно!

Поделиться
Скачать
background image

8-9

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 8      Troubleshooting the System

Setting Downstream Test Signals

Syntax Description

The following example shows how to change the power-adjustment method when the frequency 
adjustment packet count reaches 50 percent:

Router(config-if)# 

cable upstream 0 freq-adj averaging 50

Setting Downstream Test Signals

This feature provides configuration commands that allow you to create downstream test signals. Both 
pseudo random bit stream (PRBS) and unmodulated carrier test signals are now supported.

A PRBS test signal is a random data pattern that has been modulated to look like a real data stream. An 
unmodulated test signal is a continuous sine wave that looks like a carrier wave on the downstream 
transmission.

See the following sections for the required tasks to create PRBS and unmodulated carrier test signals:

  •

“Configuring Unmodulated Test Signals” section on page 8-9

  •

“Configuring PRBS Test Signals” section on page 8-10

 

  •

“Verifying Test Signal Output” section on page 8-10

Configuring Unmodulated Test Signals

Syntax

Description

n

Specifies the upstream port number.

averaging

Specifies that a percentage of frequency adjustment packets is 
required to change the adjustment method from the regular power 
adjustment method to the noise power-adjustment method.

% of frequency adjustment

Specifies the percentage of frequency-adjustment packets required to 
switch from the regular power-adjustment method to the noise 
power-adjustment method. Valid range is from 10 to 100 percent.

Command

Purpose

Step 1

Router(config-if)# 

cable downstream 

if-output continuous-wave

Generates an unmodulated continuous wave signal on the 
downstream channel. The interface is shut down.

Step 2

Router(config-if)# 

no cable downstream 

if-output 

Stops sending test signals. 

Note

Remember to reenable the interface to resume normal 
operations.

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

D-Link Verizon DSL-2750B Setup Manual preview
Verizon DSL-2750B
Бренд: D-Link Страницы: 6
D-Link DIR-857 Quick Installation Manual preview
DIR-857
Бренд: D-Link Страницы: 10
D-Link DSL-2740U Quick Installation Manual preview
DSL-2740U
Бренд: D-Link Страницы: 38
NAIM AV2 Update Instructions preview
AV2
Бренд: NAIM Страницы: 2
ICP DAS USA ZT-2510 Series Quick Start Manual preview
ZT-2510 Series
Бренд: ICP DAS USA Страницы: 8
Commell LS-570 User Manual preview
LS-570
Бренд: Commell Страницы: 58
Dahua NVR2104-S2 Quick Start Manual preview
NVR2104-S2
Бренд: Dahua Страницы: 6
Radicom WiFiHU2S-a/c Preliminary Designer’S Manual preview
WiFiHU2S-a/c
Бренд: Radicom Страницы: 27
Rabbit RabbitCore RCM4400W Product Manual preview
RabbitCore RCM4400W
Бренд: Rabbit Страницы: 126
4Home ControlPoint 2000 User Manual preview
ControlPoint 2000
Бренд: 4Home Страницы: 20
insys icom EBW-E Quick Installation Manual preview
EBW-E
Бренд: insys icom Страницы: 4
TP-Link TL-SG2424P User Manual preview
TL-SG2424P
Бренд: TP-Link Страницы: 176
NETGEAR RH328 Reference Manual preview
RH328
Бренд: NETGEAR Страницы: 142
Lanner FW-7551 User Manual preview
FW-7551
Бренд: Lanner Страницы: 38
Allied Telesis AT-BSTACK1 Quick Install Manual preview
AT-BSTACK1
Бренд: Allied Telesis Страницы: 34
PaloAlto Networks ION 1000 Hardware Reference Manual preview
ION 1000
Бренд: PaloAlto Networks Страницы: 28
B&B Electronics PCMCIA High Speed Serial Card CE 232HSPCC User Manual preview
PCMCIA High Speed Serial Card CE 232HSPCC
Бренд: B&B Electronics Страницы: 14
Compal KALA0 Schematics Document preview
KALA0
Бренд: Compal Страницы: 47

Бренды по названию

Популярные бренды

Загрузить еще бренды