manualshive.com logo in svg

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Серия продуктов Cisco uBR7200 – это мощные маршрутизаторы, обеспечивающие быструю и надежную связь. Вы сможете настроить устройство с помощью бесплатного руководства по настройке программного обеспечения, которое доступно для скачивания на {веб-сайте}. Управляйте своей сетью легко и эффективно!

Поделиться
Скачать
background image

1-135

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-05

Chapter 1      Overview of Cisco uBR7200 Series Software

cops tcp window-size

National ISDN Switch Types for BRI and PRI

The Cisco uBR7200 series supports many national ISDN switch types, including those that support 
Basic Rate Interface (BRI) and Primary Rate Interface (PRI). ISDN switch types are described further 
in the document titled 

ISDN Switch Types, Codes, and Values

 

on Cisco.com. 

PAD Subaddressing

In situations where the X.121 calling address is not sufficient to identify the source of the call, you can 
append a specified value to the calling address using the PAD subaddressing feature. PAD subaddressing 
allows you to create unique X.121 calling addresses by including either a physical port number or a value 
specified for a line as a subaddress to the X.121 calling address.

PAD subaddressing enables an X.25 host application to uniquely identify the source of an X.121 call. 
For example, in some bank security alarm applications, the central alarm host identifies the physical 
location of the alarm units from subaddressing information contained in the Call Request packet.

For additional information, refer to

“Configuring the Cisco PAD Facility for X.25 Connections”

 in the 

Cisco IOS Terminal Services Configuration Guide

, Release 12.2

 on Cisco.com. 

PPPoE Termination Support on Cable Interfaces

Cisco IOS Release 12.2(4)BC1 adds support for Point-to-Point Protocol over Ethernet (PPPoE) by 
allowing a direct connection to cable interfaces. PPPoE provides service-provider digital-subscriber line 
(DSL) support. The support of PPPoE on cable interfaces of the Cisco uBR7200 series routers allows 
customer premises equipment (CPE) behind the cable modem to use PPP as a mechanism to get their IP 
addresses and use it for all subsequent data traffic, just like a dial-up PPP client. In a PPP dial-up session, 
the PPPoE session is authenticated and the IP address is negotiated between the PPPoE client and the 
server, which could be either a Cisco uBR7200 series router or a Home Gateway.

Additional information about configuring PPPoE is available in the following documents:

  •

Configuring Broadband Access: PPP and Routed Bridge Encapsulation

 chapter of the 

Cisco IOS 

Wide-Area Networking Configuration Guide

, Release 12.2

 on Cisco.com

  •

Cisco

 

PPPoE on Ethernet

 

feature module on Cisco.com

  •

RFC 2516

Table 15

Line Cards and Port Adapters Supporting MLPPP on the Cisco uBR7200 Series for 
Cisco IOS Release 12.3(13a)BC

Model

NPE

Line Card

Port Adapter

Cisco uBR7246VXR NPE-400, NPE-G1

MC16C, MC16S, 
MC28C, MC28U

PA-4T+, 
PA-MC-2E1/120, 
PA-MC-4T1

Cisco uBR7114

N/A

N/A

PA-4E1G/120, 
PA-4T+, 
PA-MC-4T1

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

XMG OASIS Disassembly Procedure preview
OASIS
Бренд: XMG Страницы: 5
Habitat M10 Installation Manual preview
M10
Бренд: Habitat Страницы: 48
NAD M10 Quick Setup Manual preview
M10
Бренд: NAD Страницы: 2
Mackie SP260 Installation Instructions preview
SP260
Бренд: Mackie Страницы: 2
Mackie SP260 Product Overview preview
SP260
Бренд: Mackie Страницы: 5
Xantrex C12 Owner'S Manual preview
C12
Бренд: Xantrex Страницы: 8
Zonet ZFS3008 Installation Manual preview
ZFS3008
Бренд: Zonet Страницы: 8
Zonet ZEW1505 Quick Installation Manual preview
ZEW1505
Бренд: Zonet Страницы: 10
Samsung NAS Series Hardware User Manual preview
NAS Series
Бренд: Samsung Страницы: 65
Quectel Wi-Fi-M.2 EVB User Manual preview
Wi-Fi-M.2 EVB
Бренд: Quectel Страницы: 23
Bridgeworks a204 Hardware Manual preview
a204
Бренд: Bridgeworks Страницы: 18
ZALMAN CNPS6500B-AlCu User Manual preview
CNPS6500B-AlCu
Бренд: ZALMAN Страницы: 4
impinj Speedway Revolution Installation And Operation Manual preview
Speedway Revolution
Бренд: impinj Страницы: 60
ETL TeleCLIENT TC7730 Series User Manual preview
TeleCLIENT TC7730 Series
Бренд: ETL Страницы: 83
ZALMAN CNPS7000C Series User Manual preview
CNPS7000C Series
Бренд: ZALMAN Страницы: 8
Eurotech Zypad WL15 Series Quick Start preview
Zypad WL15 Series
Бренд: Eurotech Страницы: 2
Supermicro AOC-STG-I2 User Manual preview
AOC-STG-I2
Бренд: Supermicro Страницы: 15
swiftech MCW5000-64RH Installation Manual preview
MCW5000-64RH
Бренд: swiftech Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды