Cisco uBR7200 Series Скачать руководство пользователя страница 164 | Manualshive

Страница: 164 / 324

background image

2-2

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 2 Configuring the Cable Modem Termination System for the First Time

Configuration Fundamentals for the Cisco uBR7200 Series

Note

These sections provide minimal configuration instructions. For additional configuration information,
refer to subsequent chapters in this guide. For examples of Cisco uBR7200 series CMTS configuration
files, refer to the

“Viewing Sample Configuration Files” section on page 2-29

.

Additional feature configuration information is available in these documents on Cisco.com:

•

Cisco Cable Modem Termination System Feature Guide

•

Cisco IOS Configuration Fundamentals Configuration Guide

, Release 12.1

•

Cisco IOS Configuration Fundamentals Command Reference

, Release 12.1

Tip

Be sure that you have appropriate addresses and values based on your network before you attempt to
configure the router. Enter the

show version

command to display the release of Cisco IOS software on

your router.

Configuration Fundamentals for the Cisco uBR7200 Series

This section describes the basic parameters of using passwords, and describes initial configuration
utilities that are available to you. This section contains the following topics:

•

Preconfiguring the Cisco uBR7200 Series, page 2-2

•

Booting and Logging onto the Cisco uBR7200 Series, page 2-5

•

Setting Password Protection on the Cisco uBR7200 Series, page 2-5

•

Recovering Passwords on the Cisco uBR7200 Series, page 2-6

Preconfiguring the Cisco uBR7200 Series

Complete these prerequisite steps before you power on and configure the Cisco uBR7200 series router:

SUMMARY STEPS

1.

Ensure that your network supports reliable broadband data transmission.

2.

Ensure that your Cisco uBR7200 series router is installed in operational fashion.

3.

Ensure that all other required headend or distribution hub routing and network interface equipment
is installed, configured, and operational (based on the supported services).

“Reviewing Your Settings and
Configurations” section on
page 2-29

Provides commands to check your settings and review any changes
to your configuration.

“Overview of the Cisco Network
Registrar for the Cisco uBR7200
Series” section on page 7-1

Provides additional cable-specific instructions about the Cisco
Network Registrar (CNR) that are pertinent to the
Cisco uBR7200 series and CMTS management.

Section

Purpose

«
...
162
163
164
165
166
...
»

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

Бренд: Accelerated Страницы: 10

Бренд: Accelerated Страницы: 4

Бренд: RadiSys Страницы: 44

PG-FlexPlus AMU-912

Бренд: ADC Страницы: 130

Бренд: Fieldbus Specialists Страницы: 39

OMB-DAQBOARD-3000 Series

Бренд: Omega Страницы: 108

Бренд: Altera Страницы: 93

NetVanta 6355 PoE

Бренд: ADTRAN Страницы: 46

Бренд: Endace Страницы: 51

Бренд: 3Ware Страницы: 4

Бренд: AXIOMTEK Страницы: 58

Бренд: Rosco Страницы: 20

Бренд: Amit Страницы: 75

TeraBridge 5845

Бренд: Proxim Страницы: 4

Бренд: ACTi Страницы: 12

LOYTEC LIP‑3ECTC

Бренд: DELTA GROUP Страницы: 4

Бренд: Datalogic Страницы: 2

Бренд: ADC Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды