manualshive.com logo in svg

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Серия продуктов Cisco uBR7200 – это мощные маршрутизаторы, обеспечивающие быструю и надежную связь. Вы сможете настроить устройство с помощью бесплатного руководства по настройке программного обеспечения, которое доступно для скачивания на {веб-сайте}. Управляйте своей сетью легко и эффективно!

Поделиться
Скачать
background image

3-11

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 3      Configuring Cable Modem Interface Features

Configuring the Upstream Cable Modem Interface

Building configuration...

Current configuration:

!

interface cable5/0

ip address 10.254.254.254 255.0.0.0

no ip directed-broadcast

cable helper-address 192.168.1.1

no keepalive

cable downstream annex B

cable downstream modulation 64qam

Perform these steps if you are having difficulty with verification:

Step 1

Ensure that the cable connections are not loose or disconnected.

Step 2

Ensure that the cable interface line card is firmly seated in its chassis slot.

Step 3

Ensure that the captive installation screws are tight.

Step 4

Verify that you have entered the correct slot and port numbers.

Step 5

Verify that you selected the default if you are not certain about the modulation rate needed.

Step 6

Verify that the downstream carrier is active using the 

cable downstream if-output 

command.

Configuring the Upstream Cable Modem Interface

These configurations are required. Upstream cable interface commands configure the frequency and input 
power level of the upstream signal, in addition to error detection and correction of the upstream signal. The 
configuration of the upstream cable interface depends on the characteristics of your cable plant.

Perform the following tasks in this section to configure the upstream cable interface. 

Note

For some of these tasks, default values are adequate to configure the device. 

Task

Description

“Activating Upstream Admission 
Control” section on page 3-12

Provides information about the upstream admission control 
feature, and provides instructions to set the upstream admission 
control as a percentage of the upstream channel capacity. 

“Activating Upstream Differential 
Encoding” section on page 3-13

Provides brief explanation and instructions to activate 
differential encoding on the upstream, which is a digital 
encoding technique whereby a binary value is denoted by a 
signal change rather than a particular signal level.

“Activating Upstream Forward Error 
Correction” section on page 3-14

Provides instructions to activate forward error correction 
(FEC). The Cisco uBR7200 series CMTS uses FEC to attempt 
to correct any upstream data that might have been corrupted. 

“Activating the Upstream Ports” 
section on page 3-15

Provides instructions to activate upstream ports. Each upstream 
port must be activated to enable upstream data transmission 
from the CMs on the HFC network to the Cisco uBR7200 series 
CMTS.

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

Sagem 2604 Quick Installation Manual preview
2604
Бренд: Sagem Страницы: 19
Abocom FW200 Specifications preview
FW200
Бренд: Abocom Страницы: 1
Idis DR-8416 Operation Manual preview
DR-8416
Бренд: Idis Страницы: 123
Idis DR-6232H Installation Manual preview
DR-6232H
Бренд: Idis Страницы: 29
Idis DR-4516P Installation Manual preview
DR-4516P
Бренд: Idis Страницы: 28
Idis DirectIP DR-1304P Operation Manual preview
DirectIP DR-1304P
Бренд: Idis Страницы: 82
iDirect Evolution X1 Installation Manual preview
Evolution X1
Бренд: iDirect Страницы: 130
Patton electronics SMARTNODE 4900 Getting Started Manual preview
SMARTNODE 4900
Бренд: Patton electronics Страницы: 75
Patton electronics RocketLink-G 3088/I Getting Started Manual preview
RocketLink-G 3088/I
Бренд: Patton electronics Страницы: 61
Patton SmartNode 5200 Quick Start Manual preview
SmartNode 5200
Бренд: Patton Страницы: 12
Patton SL4020 Getting Started Manual preview
SL4020
Бренд: Patton Страницы: 84
Patton OnSite 3210 Series User Manual preview
OnSite 3210 Series
Бренд: Patton Страницы: 110
Patton electronics 4900 Series Specification Sheet preview
4900 Series
Бренд: Patton electronics Страницы: 2
Patton electronics SMARTNODE 4110 Series User Manual preview
SMARTNODE 4110 Series
Бренд: Patton electronics Страницы: 78
Patton electronics SMARTNODE 4552 Quick Start Manual preview
SMARTNODE 4552
Бренд: Patton electronics Страницы: 8
Rane CP 31 Datasheet preview
CP 31
Бренд: Rane Страницы: 4
Cytron Technologies SHIELD-2AMOTOR User Manual preview
SHIELD-2AMOTOR
Бренд: Cytron Technologies Страницы: 13
ACTi GNR-310 Quick Installation Manual preview
GNR-310
Бренд: ACTi Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды