Cisco uBR7200 Series Скачать руководство пользователя страница 235 | Manualshive

Страница: 235 / 324

background image

5-5

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 5 Managing Cable Modems on the Hybrid Fiber-Coaxial Network

Clearing Cable Modem Counters

Clearing Cable Modem Counters

To clear the counters for the CMs in the station maintenance list, use one of the following commands in
cable interface configuration mode.

Verifying Clear Cable Modem Counters

To determine if the counters in the station maintenance list are cleared, enter one of the

following

commands. The station maintenance list counter is 0.

Clearing Cable Modem Reset

To remove one or more CMs from the station maintenance list and reset the cable modem (or all CMs)
on the network, use one of the following commands in cable interface configuration mode.

Verifying Clear Cable Modem Reset

To determine if the

clear cable modem reset

command has removed a CM from the station maintenance

list and forced it to start a reset sequence, enter the

show cable modem

command.

Tip

Be sure that you entered the correct CM IP address or

MAC address

when you typed the

clear cable modem reset

command. It might take up to 30 seconds for the CM to start the reset

sequence.

Note

The

clear cable modem reset

command is useful if a Simple Network Management Protocol (SNMP)

manager is not available, or if the CM is unable to obtain an IP address or respond to SNMP messages.

Command

Purpose

clear cable modem

mac-addr

counters

Clears the counters in the station maintenance list for the CM
with a specific MAC address.

clear cable modem

ip-addr

counters

Clears the counters in the station maintenance list for the CM
with a specific IP address.

clear cable modem all counters

Clears the counters in the station maintenance list for all CMs.

Command

Purpose

show cable modem

ip-address

Displays the status of a CM identified by its IP address.

show cable modem

mac-address

Displays the status of a CM identified by its MAC address.

show cable modem

interface-address

Displays the status of all CMs on a particular upstream.

Command

Purpose

clear cable modem

mac-addr

reset

clear cable modem

ip-addr

reset

clear cable modem all reset

Removes the CM with a specific MAC address from the
station maintenance list and resets it.

Removes the CM with a specific IP address from the station
maintenance list and resets it.

Removes all CMs from the station maintenance list and resets
them.

«
...
233
234
235
236
237
...
»

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

Бренд: dbx Страницы: 8

Бренд: H3C Страницы: 21

Бренд: Niveo Страницы: 155

Proventia A1204

Бренд: Internet Security Systems Страницы: 42

Power Control Processor

Бренд: ETC Страницы: 64

Core 2 Quad Q9400

Бренд: Intel Страницы: 2

Бренд: ETAS Страницы: 82

PCIe/PXIe-6301 Series

Бренд: JYTEK Страницы: 46

Бренд: swiftech Страницы: 2

Бренд: Alcatel-Lucent Страницы: 154

Бренд: LevelOne Страницы: 4

Бренд: Xilinx Страницы: 43

ACC-BKT-AX-BEAM

Бренд: Extreme Networks Страницы: 35

Бренд: WIN Enterprises Страницы: 25

Бренд: ICP DAS USA Страницы: 8

Бренд: TEC Control Страницы: 4

Бренд: Z3 Technology Страницы: 83

ClareVision CV-M161620-04

Бренд: Clare Controls Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды