manualshive.com logo in svg

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Серия продуктов Cisco uBR7200 – это мощные маршрутизаторы, обеспечивающие быструю и надежную связь. Вы сможете настроить устройство с помощью бесплатного руководства по настройке программного обеспечения, которое доступно для скачивания на {веб-сайте}. Управляйте своей сетью легко и эффективно!

Поделиться
Скачать
background image

3-14

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 3      Configuring Cable Modem Interface Features

Configuring the Upstream Cable Modem Interface

Verifying Upstream Differential Encoding

To determine if upstream differential encoding is activated, enter the

 show running-config

 command 

and look for the cable interface configuration information. If upstream differential encoding is enabled, 
a differential encoding entry appears in the 

show running-config 

output. If upstream differential 

encoding is disabled, no differential encoding entry appears in the output.

Perform these steps if you are having difficulty with verification:

Step 1

Ensure that the cable connections are not loose or disconnected.

Step 2

Ensure that the cable interface line card is firmly seated in its chassis slot.

Step 3

Ensure that the captive installation screws are tight.

Step 4

Verify that you have entered the correct slot and port numbers.

Step 5

Verify that you selected a valid frequency for your router.

Activating Upstream Forward Error Correction

The Cisco uBR7200 series CMTS uses forward error correction (FEC) to attempt to correct any 
upstream data that might have been corrupted. When FEC is activated, all CMs on the network also 
activate FEC. 

Note

Although upstream FEC is an option, Cisco recommends that you use upstream FEC. FEC is activated 
by default and should not be disabled.

To activate the upstream forward error correction and to enable FEC, use the following command in 
cable interface configuration mode. 

Router(config-if)# 

cable upstream 

usport

 fec

Verifying Upstream FEC

To verify whether FEC is activated or deactivated, enter the 

more system:running-config

 command and 

look for the cable interface configuration information. If FEC is enabled, an FEC entry appears in the 

show running-config command 

output. If FEC is disabled, no FEC entry appears in the output. 

Perform these steps if you are having difficulty with verification:

Step 1

Ensure that the cable connections are not loose or disconnected.

Step 2

Ensure that the cable interface line card is firmly seated in its chassis slot.

Step 3

Ensure that the captive installation screws are tight.

Step 4

Verify that you have entered the correct slot and port numbers.

Step 5

Verify that you selected a valid frequency for your router.

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

D-Link DI-106 Series Faq preview
DI-106 Series
Бренд: D-Link Страницы: 29
D-Link DGS-3700 Series User Manual preview
DGS-3700 Series
Бренд: D-Link Страницы: 292
D-Link DGS-3224SR User Manual preview
DGS-3224SR
Бренд: D-Link Страницы: 140
D-Link DGS-1224T - Web Smart Switch User Manual preview
DGS-1224T - Web Smart Switch
Бренд: D-Link Страницы: 61
D-Link DI-LB604 - Load Balancing Router Quick Installation Manual preview
DI-LB604 - Load Balancing Router
Бренд: D-Link Страницы: 14
D-Link DIR-605L Specification preview
DIR-605L
Бренд: D-Link Страницы: 2
D-Link DIR-510L Manual preview
DIR-510L
Бренд: D-Link Страницы: 45
D-Link DES-3550 Manual preview
DES-3550
Бренд: D-Link Страницы: 218
D-Link DES-3528 - xStack Switch - Stackable User Manual preview
DES-3528 - xStack Switch - Stackable
Бренд: D-Link Страницы: 322
D-Link DIR-130 - Broadband VPN Router How To Set Up preview
DIR-130 - Broadband VPN Router
Бренд: D-Link Страницы: 10
D-Link DIR-130 - Broadband VPN Router Troubleshooting Manual preview
DIR-130 - Broadband VPN Router
Бренд: D-Link Страницы: 4
D-Link DIR-130 - Broadband VPN Router Configuration preview
DIR-130 - Broadband VPN Router
Бренд: D-Link Страницы: 13
D-Link DIR Series Configuration Manual preview
DIR Series
Бренд: D-Link Страницы: 13
D-Link DI-804HV - Express ENwork Router Configuration Manual preview
DI-804HV - Express ENwork Router
Бренд: D-Link Страницы: 19
D-Link DI-808HV Quick Installation Manual preview
DI-808HV
Бренд: D-Link Страницы: 12
D-Link DI-804 Quick Install Manual preview
DI-804
Бренд: D-Link Страницы: 8
D-Link DI-604UP Quick Install Manual preview
DI-604UP
Бренд: D-Link Страницы: 16
D-Link DI-304 Technical Bulletin preview
DI-304
Бренд: D-Link Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды