manualshive.com logo in svg

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Серия продуктов Cisco uBR7200 – это мощные маршрутизаторы, обеспечивающие быструю и надежную связь. Вы сможете настроить устройство с помощью бесплатного руководства по настройке программного обеспечения, которое доступно для скачивания на {веб-сайте}. Управляйте своей сетью легко и эффективно!

Поделиться
Скачать
background image

1-142

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-05

Chapter 1      Overview of Cisco uBR7200 Series Software

DOCSIS and CMTS Interoperability

Traffic Engineering

Sending data reliably upstream is a critical issue. Designing a robust upstream architecture requires 
balancing system parameters, establishing subscriber data requirements, and configuring the network to 
support those requirements. 

Upstream spectrum varies greatly between cable plants. Maintaining stable return paths also differs 
based on varying patterns and levels of ingress noise and interference. Common problems in cable plants 
include:

  •

Electrical and magnetic interference (EMI)

  •

Thermal noise

  •

Carrier to noise (C/N) imbalances

  •

Interference of leaking signals

  •

Ingress due to other channels appearing at the desired channel frequency

  •

Distortion due to non-linearities of cable equipment

  •

Cross modulation—carrier to frequency distortion

  •

Hum and low frequency distortion

  •

Improper RF amplifier tuning

  •

Non-unity gains due to incorrect usage of attenuators

  •

Low-quality subscriber equipment

  •

Out of range signal power from the CMTS to the cable modem

When configuring your system, configure downstream and upstream parameters based on the fiber nodes 
involved, the required services the cable modem or STB supports, the importance of the data, and desired 
performance capabilities. 

Your cable plant determines its data performance. Design your network to maximize its performance and 
capacity at minimum cost, while meeting subscriber data requirements. Select or customize upstream 
profiles for maximum trade-offs between bandwidth efficiency and upstream channel robustness once 
you’re familiar with the system and have characterized your network. For example, QAM-16 requires 
approximately 7 dB higher C/N ratio to achieve the same bit error rate (BER) as QPSK, but it transfers 
information at twice the rate of QPSK. 

Note

Older plants and plants with long amplifier cascades are more susceptible to ingress than newer plants. 
These plants produce more noise and signal level variances.

Tip

Cisco recommends you keep input to all amplifiers at the same power level in the upstream direction and 
keep output of all amplifiers in the downstream direction at the same power level. This is called unity 
gain. Tune amplifiers and other equipment properly at desired frequencies. To characterize and improve 
your cable plant’s stability, follow procedures in the 

Cisco uBR7200 Series Universal Broadband Router 

Hardware Installation Guide

 on Cisco.com. 

A DOCSIS cable plant has the following groups of traffic to size based on current service offerings:

  •

Basic Internet access data, which is burst-intensive and asymmetrical; asymmetrical traffic supports 
a larger data rate in one direction—the downstream.

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

Sagem 2604 Quick Installation Manual preview
2604
Бренд: Sagem Страницы: 19
F5 WANJet 500 Quick Start Card preview
WANJet 500
Бренд: F5 Страницы: 2
F5 ARX-500 Hardware Reference Manual preview
ARX-500
Бренд: F5 Страницы: 90
F5 ARX-4000 Parts Replacement Manual preview
ARX-4000
Бренд: F5 Страницы: 47
Queclink GV600 Series Instruction Manual preview
GV600 Series
Бренд: Queclink Страницы: 9
NetBurner MOD5272 Quick Start Manual preview
MOD5272
Бренд: NetBurner Страницы: 15
ZyXEL Communications P-336M Quick Start Manual preview
P-336M
Бренд: ZyXEL Communications Страницы: 125
Telex Communications 2472AA Instruction Manual preview
2472AA
Бренд: Telex Communications Страницы: 28
IDT USB-BRIDGEV2-EVAL Evaluation Board Manual preview
USB-BRIDGEV2-EVAL
Бренд: IDT Страницы: 11
Ubiquiti EdgeRouter PRO Quick Start Manual preview
EdgeRouter PRO
Бренд: Ubiquiti Страницы: 20
HPE FlexNetwork 5130 Series Troubleshooting Manual preview
FlexNetwork 5130 Series
Бренд: HPE Страницы: 33
TP-Link TL-SL2226P+ User Manual preview
TL-SL2226P+
Бренд: TP-Link Страницы: 37
Wyse C90LE7 Quick Start Manual preview
C90LE7
Бренд: Wyse Страницы: 8
S&P Turbo-3000 Operating Instructions preview
Turbo-3000
Бренд: S&P Страницы: 3
ProSoft MVI46-PDPS User Manual preview
MVI46-PDPS
Бренд: ProSoft Страницы: 53
Antec KÜHLER H2O 920 Software Manual preview
KÜHLER H2O 920
Бренд: Antec Страницы: 6
Knowles IA611 Xplained Pro User Manual preview
IA611 Xplained Pro
Бренд: Knowles Страницы: 14
Mobily NTC-40WV-QSG Quick Start Manual preview
NTC-40WV-QSG
Бренд: Mobily Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды