manualshive.com logo in svg

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Серия продуктов Cisco uBR7200 – это мощные маршрутизаторы, обеспечивающие быструю и надежную связь. Вы сможете настроить устройство с помощью бесплатного руководства по настройке программного обеспечения, которое доступно для скачивания на {веб-сайте}. Управляйте своей сетью легко и эффективно!

Поделиться
Скачать
background image

2-20

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 2      Configuring the Cable Modem Termination System for the First Time

Configuring the Cisco uBR7200 Series Using the Setup Facility

Step 6

The Simple Network Management Protocol (SNMP) is the most widely supported open standard for 
network management. SNMP provides a means to access and set configuration and run-time parameters 
of routers and communication servers. SNMP also defines a set of functions that can be used to monitor 
and control network elements.

Enter 

yes

 to accept SNMP management; enter 

no

 to refuse it:

Configure SNMP Network Management? [no]:

    Community string [public]:

Step 7

In all cases, you will use IP routing. When you are using IP routing, select an interior routing protocol. 
You can specify one of only two interior routing protocols to operate on your system using the Setup 
facility, either Interior Gateway Routing Protocol (IGRP) or Routing Information Protocol (RIP). 

To configure IP routing, enter 

yes

 (the default) or press 

Return

, and then select an interior routing protocol:

  Configure IP? [yes]:

    Configure IGRP routing? [yes]:

      Your IGRP autonomous system number [1]: 

15

Step 8

Configure your line card interface parameters. The following example shows how an 8-port Ethernet line 
card is installed in line card slot 3. The Setup facility determines the status of all interfaces.

To configure each active interface port for IP, enter 

yes

 (the default) or press 

Return

. For all inactive 

ports, the default is 

no

. You can press 

Return

 to accept the default. 

Configuring interface Ethernet 1/0:
  Is this interface in use? [yes]: 
  Configure IP on this interface? [yes]: 
    IP address for this interface [19.2.22.4]: 
    Number of bits in subnet field [8]: 
    Class A network is 19.0.0.0, 8 subnet bits; mask is /16

Configuring interface Ethernet1/1:
  Is this interface in use? [no]: 

Configuring interface Ethernet1/2:
Is this interface in use? [no]: 

Configuring interface Ethernet1/3:
  Is this interface in use? [no]: 

Configuring interface Ethernet1/4:
  Is this interface in use? [no]: 

Configuring interface Ethernet1/5:
  Is this interface in use? [no]: 

Configuring interface Ethernet1/6:
  Is this interface in use? [no]: 

Configuring interface Ethernet1/7:
  Is this interface in use? [no]: 

Step 9

Configure your cable interface. The following example shows a Cisco uBR7200 series router with cable 
interface. The Setup facility, for the most part, determines the status of all interfaces.

To configure each active interface port, enter 

yes

 (the default) or press 

Return

. For all inactive ports, the 

default is 

no

. You can press 

Return

 to accept the default. 

Configuring interface cable 5/0:
  Is this interface in use? [yes]: 
  Configure this interface? [yes]: 
  IP address for this interface [19.2.22.5]: 
  Number of bits in subnet field [8]: 
  Class A network is 19.0.0.0, 8 subnet bits; mask is /16

Configuring interface cable 1/1:

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

Quantum Scalar 50 Upgrade Instructions preview
Scalar 50
Бренд: Quantum Страницы: 20
Freescale Semiconductor MCF54455 Reference Manual preview
MCF54455
Бренд: Freescale Semiconductor Страницы: 921
N.A.T. NAT-MCH Technical Reference Manual preview
NAT-MCH
Бренд: N.A.T. Страницы: 32
IntesisBox IBOX-BAC Series Installation Sheet preview
IBOX-BAC Series
Бренд: IntesisBox Страницы: 2
Linksys WRT54GR - Wireless-G Broadband Router Quick Installation Manual preview
WRT54GR - Wireless-G Broadband Router
Бренд: Linksys Страницы: 81
NEC Thin Client US310e Getting Started preview
Thin Client US310e
Бренд: NEC Страницы: 6
HELVAR Imagine 920 Installation Manual preview
Imagine 920
Бренд: HELVAR Страницы: 2
ZALMAN CNPS12X User Manual preview
CNPS12X
Бренд: ZALMAN Страницы: 11
ETL TeleCLIENT TC7730 Series User Manual preview
TeleCLIENT TC7730 Series
Бренд: ETL Страницы: 83
Belden HIRESCHMANN IT MAMMUTHUS MTM8003-FAN User Manual preview
HIRESCHMANN IT MAMMUTHUS MTM8003-FAN
Бренд: Belden Страницы: 84
OWC Mercury FireWire 400 Owner'S Manual preview
Mercury FireWire 400
Бренд: OWC Страницы: 2
Intel RS25AB080 Tested Hardware And Operating System List preview
RS25AB080
Бренд: Intel Страницы: 26
Quantum QWCM Installation Manual preview
QWCM
Бренд: Quantum Страницы: 7
ARTERY AT32F421 Series Reference Manual preview
AT32F421 Series
Бренд: ARTERY Страницы: 337
ekwb EK-FC980 GTX Classy Installation And Mounting Manual preview
EK-FC980 GTX Classy
Бренд: ekwb Страницы: 2
Ubiquiti UniFi WiFi BaseStation XG Quick Start Manual preview
UniFi WiFi BaseStation XG
Бренд: Ubiquiti Страницы: 19
CG Emotron OSTO 100 Instruction Manual preview
Emotron OSTO 100
Бренд: CG Страницы: 112
TP-Link TL-MR3620 Installation Manual preview
TL-MR3620
Бренд: TP-Link Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды