Cisco uBR7200 Series Скачать руководство пользователя страница 98

Страница: 98 / 324

1-80

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-05

Chapter 1 Overview of Cisco uBR7200 Series Software

cops tcp window-size

New and Changed Commands

cable match address

Use the existing “cable match” command to assign QoS to a multicast group, with BPI either enabled or
disabled.

router# cable match address <

number

>|<

name

> [service-class <

name

> [bpi-enable]]

router# no cable match address [<

number

>|<

name

> [service-class <

name

> [bpi-enable]]]

debug cable mcast-qos

Use this command to turn on CMTS Multicast Qos debugging.

router# debug cable mcast-qos

IP Routing Features

The Cisco uBR7200 series router offers you several features to assist with IP routing configuration and
performance.

•

Cable ARP Filter Enhancement, page 1-80

•

cable intercept Command, page 1-81

•

Cable Interface Bundling and Cable Subinterfaces, page 1-82

•

Configurable Alternate Termination System Information Messages, page 1-83

•

Easy IP (Phase 1), page 1-83

•

Fast-Switched Policy Routing, page 1-83

•

IP Enhanced IGRP Route Authentication, page 1-84

•

IP Network Address Translation/Port Address Translation, page 1-84

•

NAT—Support for NetMeeting Directory (Internet Locator Service—ILS), page 1-84

•

Router-Port Group Management Protocol, page 1-85

•

Supported Protocols on the Cisco uBR7200 Series, page 1-85

Cable ARP Filter Enhancement

The

cable arp filter

command, introduced with Cisco IOS Release 12.2(15)BC2b, enables service

providers to filter ARP request and reply packets. This prevents a large volume of such packets from
interfering with the other traffic on the cable network.

Cisco IOS Release 12.3(9a)BC introduces enhanced command option syntax for the

cable arp filter

command, where

number

and

window-size

values are optional for

reply-accept

and

request-send

settings.

Содержание uBR7200 Series





































































































































































































































































































































Результаты поиска

Содержание uBR7200 Series

Отзывы:

Похожие инструкции для uBR7200 Series

Бренды по названию

Популярные бренды

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Результаты поиска

Содержание uBR7200 Series

Отзывы:

Похожие инструкции для uBR7200 Series

Бренды по названию

Популярные бренды