Cisco uBR7200 Series Скачать руководство пользователя страница 185 | Manualshive

Страница: 185 / 324

background image

2-23

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 2 Configuring the Cable Modem Termination System for the First Time

Configuring the Cisco uBR7200 Series Using the Setup Facility

Configuring Synchronous Serial Interfaces

The synchronous serial interfaces are configured to allow connection to WANs through a CSU/DSU.
Complete the following steps to configure the serial ports:

Step 1

To configure serial port 0 enter yes:

Configuring interface Serial0/0:

Is this interface in use? [no]:

yes

Step 2

Determine which protocols you want on the synchronous serial interface and enter the appropriate
responses:

Configure IP unnumbered on this interface? [no]:

IP address for this interface: 10.1.1.20

Number of bits in subnet field [0]:

Class A network is 10.0.0.0, 0 subnet bits; mask is 255.0.0.0

Step 3

If additional synchronous serial interfaces are available in your system, enter their configurations when
you are prompted.

Step 4

Save the configuration to NVRAM:

Router#

copy running-config startup-config

Note

You must always manually save the configuration settings to NVRAM whenever they are modified.

The following sample display includes a continuous listing of all interface configuration parameters
selected for Ethernet and synchronous serial interfaces. These parameters are shown in the order in
which they appear on your console terminal.

Tip

Only one Ethernet and one synchronous serial interface are configured for this example.

Configuring interface parameters:

Configuring interface Ethernet0/0:
Is this interface in use? [no]: yes

Configure IP on this interface? [no]: yes

IP address for this interface: 10.1.1.10

Number of bits in subnet field [0]:
Class A network is 10.0.0.0, 0 subnet bits; mask is 255.0.0.0
Configure IPX on this interface? [no]:
Configure AppleTalk on this interface? [no]: no

Configuring interface Serial0/0:
Is this interface in use? [no]: yes

Configure IP on this interface? [no]: yes

Configure IP unnumbered on this interface? [no]:
IP address for this interface: 10.1.1.20

Number of bits in subnet field [0]:
Class A network is 10.0.0.0, 0 subnet bits; mask is 255.0.0.0
Configure IPX on this interface? [no]:
Configure AppleTalk on this interface? [no]:

«
...
183
184
185
186
187
...
»

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

All in One Printer

Бренд: Baracoda Страницы: 42

Бренд: GE Страницы: 146

Бренд: Mackie Страницы: 2

Бренд: Mackie Страницы: 5

Бренд: Data Translation Страницы: 98

Бренд: Paradyne Страницы: 11

Бренд: Paradyne Страницы: 19

Бренд: Paradyne Страницы: 32

COMSPHERE 3550 Series

Бренд: Paradyne Страницы: 153

Jetstream CPX-1000

Бренд: Paradyne Страницы: 141

FrameSaver 9783

Бренд: Paradyne Страницы: 28

Бренд: Ubiquiti Страницы: 22

Бренд: Ublox Страницы: 17

Бренд: Accusys Страницы: 34

Ethernet Communication Module DVPEN01-SL

Бренд: Delta Electronics Страницы: 54

Brocade X6-8 Director

Бренд: Broadcom Страницы: 207

Бренд: Juniper Страницы: 190

Бренд: Lanner electronics Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды