Cisco uBR7200 Series Скачать руководство пользователя страница 215 | Manualshive

Страница: 215 / 324

background image

3-23

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 3 Configuring Cable Modem Interface Features

Configuring the Upstream Cable Modem Interface

Tip

For National Television Standards Committee (NTSC) operations, valid ranges are 5000000 to
42000000 Hz.

Caution

Some cable systems cannot reliably transport frequencies near these band edges. The wider the upstream
channel (in MHz), the more difficulty you might have. Enter a center frequency between 20 and 38 MHz
if you have difficulty.

Note

You can also select a default that does not set a specific fixed value. The Cisco uBR7200 series software
instructs the cable interfaces to use this frequency as the center frequency.

Verifying the Upstream Frequency

To verify the current value of the upstream frequency, enter the

show controllers cable

command for

the upstream port you have just configured:

Router#

show controllers cable5/0 u0

Cable5/0 Upstream 0 is up

Frequency 24.016 MHz, Channel Width 1.600 MHz, QPSK Symbol Rate 1.280 Msps

Spectrum Group is overridden

SNR 33.2560 dB

Nominal Input Power Level 0 dBmV, Tx Timing Offset 2288

Ranging Backoff automatic (Start 0, End 3)

Ranging Insertion Interval automatic (60 ms)

Tx Backoff Start 0, Tx Backoff End 4

Modulation Profile Group 1

Note

The upstream frequency displayed in the

show controllers cable

command output might not match the

frequency that you entered when you set the upstream frequency. The Cisco uBR7200 series CMTS
might select an upstream frequency close to the frequency you entered that offers better performance.
The Cisco uBR7200 series CMTS selects the closest frequency available.

Perform these steps if you are having difficulty with verification:

Step 1

Ensure that the cable connections are not loose or disconnected

Step 2

Ensure that the cable interface line card is firmly seated in its chassis slot.

Step 3

Ensure that the captive installation screws are tight.

Step 4

Verify that you have entered the correct slot and port numbers.

Step 5

Verify that you have selected a valid frequency for your router.

Command

Purpose

Step 1

Router(config-if)#

cable upstream

usport

frequency

up-freq-hz

Enters the fixed center frequency for your upstream
RF carrier in Hz.

Step 2

Router(config-if)#

no cable upstream

usport

shutdown

Places the upstream port in the “admin up” state.

«
...
213
214
215
216
217
...
»

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

Бренд: IBM Страницы: 72

Бренд: Mackie Страницы: 2

Бренд: Mackie Страницы: 5

DR-4100P Series

Бренд: Idis Страницы: 30

Бренд: Accusys Страницы: 34

Бренд: NXP Semiconductors Страницы: 24

Бренд: Fortinet Страницы: 20

PG-FlexPlus AMU-912

Бренд: ADC Страницы: 130

Бренд: Fieldbus Specialists Страницы: 39

Бренд: LogLogic Страницы: 30

Бренд: Mercusys Страницы: 35

NI WLS/ENET-9163

Бренд: National Instruments Страницы: 36

Бренд: EMCIS Страницы: 14

Бренд: 1&1 Страницы: 32

WNFB-265AXI(BT)

Бренд: Sparklan Страницы: 14

Бренд: Lanner Страницы: 38

Бренд: Allied Telesis Страницы: 34

Imagestore Intuition+

Бренд: Miranda Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды