manualshive.com logo in svg

Cisco uBR7200 Series, Руководство по настройке программного обеспечения

Серия продуктов Cisco uBR7200 – это мощные маршрутизаторы, обеспечивающие быструю и надежную связь. Вы сможете настроить устройство с помощью бесплатного руководства по настройке программного обеспечения, которое доступно для скачивания на {веб-сайте}. Управляйте своей сетью легко и эффективно!

Поделиться
Скачать
background image

8-10

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-03

Chapter 8      Troubleshooting the System

Pinging Unresponsive Cable Modems

Configuring PRBS Test Signals

Verifying Test Signal Output

To verify the output of a continuous wave test signal or the output of a PRBS test signal, use a spectrum 
analyzer on the downstream channel. The downstream carrier is enabled as a default.

The standard mode of operation is modulated signal output and the interface is active. For PRBS and 
continuous wave output, the selected interface is shut down. 

The functioning of the 

no cable downstream if-output 

command has not changed. The interface is shut 

down.

Pinging Unresponsive Cable Modems

Pinging a Cable Modem

Ping DOCSIS is a Cisco patent-pending feature that allows a cable system administrator to quickly 
diagnose the health of a channel between the Cisco uBR7200 series routers and the cable interface. The 
technology uses 1/64—the bandwidth of IP ping—and works with CMs that do not have an IP address. 
This allows cable operators to ping CMs that are unable to complete registration, that have internal bugs, 
or that are unresponsive due to a crash. 

The Ping DOCSIS feature includes a real-time view and plot of requested power adjustments, and a 
measure of optimal headend reception power. This gives the cable operator the ability to solicit a 
configurable number of periodic ranging requests from a cable interface.

To ping a specific cable interface to determine if it is online, use the following command in EXEC mode.

Verifying the Ping

The 

ping docsis

 command returns a verification from a CM that is pinged:

Queuing 5 MAC-layer station maintenance intervals, timeout is 25 msec:

!!!!!

Success rate is 100 percent (5/5)

Command

Purpose

Step 1

Router(config-if)# 

cable downstream 

if-output prbs

Generates a PRBS test signal on the downstream channel. The 
interface is shut down.

Step 2

Router(config-if)# 

no cable downstream 

if-output 

Stops sending test signals. 

Note

Remember to reenable the interface to resume normal 
operations.

Command

Purpose

Step 1

Router# 

ping docsis

 

addr

Pings the CM with a specific MAC address or IP address to see if it is online.

Содержание uBR7200 Series





































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для uBR7200 Series

M-Audio Computer Quick Start Manual preview
Computer
Бренд: M-Audio Страницы: 10
Accelerated 6330-MX User Manual preview
6330-MX
Бренд: Accelerated Страницы: 10
Accelerated 6300-CX Customer Setup Instructions preview
6300-CX
Бренд: Accelerated Страницы: 4
WaiLan DeltaFire 500 User Manual preview
DeltaFire 500
Бренд: WaiLan Страницы: 27
Bridgeworks Oresund EFC102200 User Manual preview
Oresund EFC102200
Бренд: Bridgeworks Страницы: 84
Supersonic Franky Instruction Manual preview
Franky
Бренд: Supersonic Страницы: 46
Quantum QWCM Installation Manual preview
QWCM
Бренд: Quantum Страницы: 7
ARTERY AT32F421 Series Reference Manual preview
AT32F421 Series
Бренд: ARTERY Страницы: 337
NETGEAR RP614 - Web Safe Router Installation Manual preview
RP614 - Web Safe Router
Бренд: NETGEAR Страницы: 16
ATI Technologies RADEON 9800 PRO Getting Started Manual preview
RADEON 9800 PRO
Бренд: ATI Technologies Страницы: 20
JLCooper Electronics GangWay32 User Manual preview
GangWay32
Бренд: JLCooper Electronics Страницы: 12
LUX LUMEN 10230 Manual preview
10230
Бренд: LUX LUMEN Страницы: 41
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Бренд: Vivint Страницы: 2
Stephen SON8010U User Manual preview
SON8010U
Бренд: Stephen Страницы: 8
ekwb EK-Quantum Vector FTW3 RTX 2080 Ti Installation Manual preview
EK-Quantum Vector FTW3 RTX 2080 Ti
Бренд: ekwb Страницы: 3
VANTAS DPA-S50 Owner'S Manual preview
DPA-S50
Бренд: VANTAS Страницы: 30
N-Tron 104TX Specification Sheet preview
104TX
Бренд: N-Tron Страницы: 2
OWC ACCELSIOR 8M2 Assembly Manual & User Manual preview
ACCELSIOR 8M2
Бренд: OWC Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды