Challenge 130TC-A-160000 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 282

background image

MAY 2019

CMT-130TC Book Trimmer

2-77

2. Status Indicator RAPs

RAP 2.69 Stacker Tray Up/Down Cyl-
inder

Stacker I/O PWB Output 6

The tray up/down cylinder is used to lift the roller
tray up and down. The Book In sensor detects
when a book is completely in the roller tray, trig-
gering the cylinder to lift the tray to the horizontal
position, ready for the tray to dump the book
onto the output table. The tray up/down cylinder
is located under the roller tray, as shown in Fig-
ure 2-107.

Possible Fault Indicators



The roller tray does not lift horizontally.



The tray up/down cylinder does not ac-
tuate when it should.

Initial Actions

Perform RAP 2.20 Pneumatic Pressure.

Check that all cables and air tubing between the
trimmer and Stacker are securely fastened and
are not damaged.

Perform GP 6.14 Speed-Control Air Valves.

Check that all air hoses in the Stacker are con-
nected properly, and are not damaged or
pinched.

Check for loose or damaged wire 72 at the
Stacker electrical panel.

Check that cable #1 is connected to the air valve
properly.

Procedure

1. Remove the rear panel on the Stacker and

locate the tray up/down cylinder. Fully open
the flow control valves located at the air fit-
tings on the cylinder.

2. Switch the main air ON and main power ON.

3. Manually activate the tray up/down air valve

by pressing the actuator button on the valve
(Figure 2-107). Does roller tray lift to the
horizontal position?

Y N

Disconnect main power and replace the
valve (PL 5.66 Stacker Air Manifold 58008).

4. Electrically activate the valve by shorting

wire 72 to wire 74. Does the valve actuate
and the roller tray lift to the horizontal posi-
tion?

Y N

Disconnect main power and replace the
valve (PL 5.66 Stacker Air Manifold 58008).

5. Check for loose or damaged cables between

the trimmer and Stacker. Check for proper
hose and wire connections inside the
Stacker. Did this fix the problem?

Y N

Disconnect power and replace the Stacker
I/O PWB (REP 4.26 Accessory PWB Re-
placement).

6. Readjust the flow control valves so that the

tray up/down cylinder moves at a moderate
speed (GP 6.14 Speed-Control Air Valves).

Figure 2-107. Tray Up/Down Cylinder, Valve

«
...
87
88
89
90
91
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: Makita Страницы: 100

Бренд: Echo Страницы: 20

Бренд: Homelite Страницы: 60

Бренд: GreenWorks Страницы: 28

Бренд: Yardworks Страницы: 24

Бренд: Echo Страницы: 8

Бренд: GreenWorks Страницы: 214

Бренд: Cobra Страницы: 47

Swingline ClassicCut lite 9312

Бренд: ACCO Brands Страницы: 2

Бренд: Silvercrest Страницы: 37

Бренд: Silvercrest Страницы: 68

Бренд: Silvercrest Страницы: 83

Бренд: Dolmar Страницы: 148

Бренд: Leviton Страницы: 2

Attraxion Classic

Бренд: OBH Nordica Страницы: 52

Бренд: Shindaiwa Страницы: 48

Бренд: Shindaiwa Страницы: 72

Бренд: Flymo Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды