manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 264

 

 

 

MAY 2019 

 

8. Installation

 

8-4 

CMT-130TC Book Trimmer 

5.  Wheel the elevator into approximate position 

next to the tilt infeed conveyor. 

6.  Turn down the leveling pads until the top 

shelf is 36-1/32" (91.5 cm) from the floor as 
shown in Figure 8-8. 

 

 

Figure 8-8. Elevator Height Setting 

7.  Align the elevator with the infeed conveyor 

and attach as shown in Figure 8-9 using the 
hardware provided. 

 

Figure 8-9. Elevator Attachment to 

Infeed Conveyor 

8.  On the trimmer, adjust the height of the in-

feed bracket (Figure 8-10) if necessary.  The 
flat, horizontal surface of the bracket should 
be 1/32” (1mm) below the trimmer's infeed 
conveyor belt. 

 

Figure 8-10. Infeed Bracket 

9.  Move the trimmer into position against the 

elevator, aligning the mounting brackets on 
the elevator to the corresponding holes in 
the side of the trimmer.  Once the trimmer 
height is set properly according to Section 
8.5 Trimmer Height Setup, attach the eleva-
tor to the trimmer using supplied mounting 
hardware (Figure 8-11).  

 

Figure 8-11. Elevator Attachment to Trimmer 

Cable and Air Tubing Connections 
(Tilt Co Elevator) 

1.  Remove the lower front panel of the trimmer 

and locate the yellow power cable coiled up 
inside the trimmer that is labelled with the 
number that corresponds to the label on the 
elevator near the input connectors.  The 
power cables are the larger diameter cables 
with 7-pin connectors on the end.   

2.  Route the power cable under the hydraulic 

unit and out of the left side of the trimmer. 

3.  Connect the power cables as shown in Fig-

ure 8-12.  

 

 

Figure 8-12. Power Cable Connections 

4.  Now locate the yellow communication cable 

coiled up inside the trimmer that is labelled 
with the number that corresponds to the la-
bel on the elevator near the input connect-
ors.  It is a small diameter cable with a 3-pin 
connector on the end.  Also locate any sepa-
rate communication cables that were sup-
plied with the infeed/outfeed options. 

5.  Connect the communication cables as 

shown in Figure 8-13.  

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды