manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 232

 

 

 

MAY 2019 

 

6. General Procedures/Information

 

6-18 

CMT-130TC Book Trimmer 

rotational position, and finally the locking air 
cylinder locks the gripper assembly in the 
exact rotational position. 

12.  Once rotated, the gripper moves the book to 

the proper cutting position for the bottom 
trim. 

13.  The bottom trim is performed by the knife 

and clamp in the same way as described 
earlier. 

14.  The gripper assembly rotates the book 180° 

clockwise, in the same way as described 
earlier.  Once rotated, the gripper moves the 
book to the proper cutting position for the 
top trim. 

15.  The top trim is performed by the knife and 

clamp in the same way as described earlier. 

16.  The gripper assembly rotates the book 90° 

counterclockwise, in the same way as de-
scribed earlier.  

17.  The gripper transport then takes the book 

back to home position. 

18.  At the home position, the book is released 

and the conveyors start moving.  The book 
exits the machine onto the installed outfeed 
device. 

Additional Information 

 

The trimmer also provides a shutdown 
relay that can be used to signal other in-
line equipment that it is running or 
paused. 

Sequence of Operations 

– Outfeed 

Option 1: Vertical Book Stacker 

1.  As the book exits the trimmer, the rollers in 

the upper tray move the book completely 
into the upper tray.  A sensor in the upper 
tray detects when the book is completely 
loaded. 

2.  An air cylinder lifts the lower end of the up-

per tray until it is level. 

3.  A second air cylinder lifts the side of the up-

per tray, allowing the book to be ejected off 
from the upper tray and down onto the Verti-
cal Stacker delivery bed.  If the book is more 
than 1” (2.5cm) thick, a pusher assembly 
powered by an air cylinder retracts slightly to 
allow more room for thicker books. 

4.  A sensor detects when the book lands onto 

the delivery bed. 

5.  Then a fingered gate powered by an air cyl-

inder drops down, and the pusher assembly 
moves the book to the other side of the fin-
gered gate.  A spring-loaded book stop 
keeps the books upright. 

6.  The fingered gate returns to the up position 

and the pusher retracts to its starting posi-
tion.   

7.  Books accumulate on the delivery bed until 

the spring-loaded book stop reaches a sen-
sor at the end of the delivery bed indicating 
that the Vertical Stacker is full.  When the 
Vertical Stacker is full, no more books are 
delivered from the trimmer until the delivery 
bed is cleared of books and the book stop is 
retracted. 

Option 2: Exit Conveyor 

1.  As the book exits the trimmer, the Exit Con-

veyor runs.  The length of time that the Exit 
Conveyor runs for each book is determined 
by a time delay relay, which is adjustable by 
the potentiometer found on the front face of 
the conveyor. 

2.  Book accumulate on the Exit Conveyor until 

they reach the sensor at the end of the con-
veyor.  When the sensor detects a book, the 

conveyor stops and no more books are de-
livered from the trimmer until the sensor is 
cleared of books. 

Option 3: Exit Chute 

1.  As the book exits the trimmer, it slides down 

the Exit Chute and into a container placed 
underneath the end of chute. 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды