Challenge 130TC-A-160000 Скачать руководство пользователя страница 266 | Manualshive

Страница: 266 / 282

Challenge 130TC-A-160000 Скачать руководство пользователя страница 266

MAY 2019

8. Installation

8-6

CMT-130TC Book Trimmer

Infeed Option 2:
Tilt Conv. + El Pile Feeder

Figure 8-15. Infeed Conv. + El Pile

Feeder

Setup Procedure

1. Perform installation steps 1 through 8 for In-

feed Option 1, Tilt Co Elevator.

2. Setup the book pile feeder according to the

instruction and parts manual supplied with
the book pile feeder.

3. Attach the pile feeder to the elevator.

4. Move the trimmer into position against the

pile feeder, aligning the mounting brackets
on the pile feeder to the corresponding holes
in the side of the trimmer. Once the trimmer
height is set properly according to Section
8.5 Trimmer Height Setup, attach the pile
feeder to the trimmer using supplied mount-
ing hardware.

Cable and Air Tubing Connections

1. Remove the lower front panel of the trimmer

and locate the yellow power cable coiled up
inside the trimmer that is labelled with the
number that corresponds to the label on the
elevator near the input connectors. The

power cables are the larger diameter cables
with 7-pin connectors on the end.

2. Route the power cable under the hydraulic

unit and out of the left side of the trimmer.

3. Connect the power cables as shown in Fig-

Figure 8-16. Power Cable Connections

4. Now locate the yellow communication cable

coiled up inside the trimmer that is labelled
with the number that corresponds to the la-
bel on the elevator near the input connect-
ors. It is a small diameter cable with a 3-pin
connector on the end. Also locate any sepa-
rate communication cables that were sup-
plied with the infeed/outfeed options.

5. Connect the communication cables as

shown in Figure 8-17.

Figure 8-17. Comm. Cable Connections

6. Now locate the coiled-up line of blue air tub-

ing with a red and white connector on the
end that is labelled with the numbers that
correspond to the labels on the pile feeder,
elevator, and tilt conveyor near the input
connectors. Also locate any separate air
tubing sections that may have been supplied
with the infeed/outfeed options.

7. Connect the air tubing as shown in Figure

«
...
264
265
266
267
268
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды