manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 231

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

6-17 

6. General Procedures/Information

 

6.  The shelf also supports the book as it 

crosses the span between the Pile Feeder 
and the trimmer.   

Option 3: In-line + Pile Feeder 

1.  This is a combination of options 1 and 2, 

where the Pile Feeder is placed in between 
the Elevator and CMT-130TC.  The Se-
quence of Operations is the same as for 
each option, with the only difference being 
that when books exit the Elevator, they pass 
through the Pile Feeder by way of the lower 
tilt table conveyor in the level position. 

Option 4: Standard Hand-Feed Conveyor 

1.  Bound books are placed in stacks of 1, 2, or 

3 books on the conveyor against a back-
stop.   

2.  The conveyor delivers books into the trim-

mer at the proper time intervals, as deter-
mined by the trimmer’s computer.  The trim-
mer controls the conveyor motor by switch-
ing power to it on or off. 

Option 5: Long Hand-Feed Conveyor 

1.  Bound books are placed in stacks of 1, 2, or 

3 books on the conveyor against a back-
stop.   

2.  The conveyor delivers books into the trim-

mer at the proper time intervals, as deter-
mined by the trimmer’s computer.  The trim-
mer controls the conveyor motor by switch-
ing power to it on or off. 

Sequence of Operations 

– Trimmer 

1.  Books enter into the trimmer on the internal 

infeed conveyor.  As a book moves along 
the conveyor, an optical distance sensor 
mounted above the conveyor measures the 
thickness of the book and relays that infor-
mation to the computer. 

2.  As the book moves across the bottom plate 

of the gripper, a retro-reflective sensor 
mounted on the gripper assembly detects 
when a book is in position and ready to be 
clamped by the gripper.  Once the book is in 
the proper position, the conveyors stop, and 
the gripper clamps the book. 

3.  The gripper lifts slightly by an air cylinder 

mounted to the gripper, then transports the 
book to the registration station using a DC 
servo motor controlling its linear motion.  As 
the book is transported, air is blasted under-
neath it to reduce friction and scratching to 
the cover.  When the book enters the regis-
tration area, a retro-reflective sensor detects 
the front and spine edges of the book as it 
passes beneath it.  This provides the com-
puter with the starting width dimension of the 
book.   

4.  The registration plate is accurately posi-

tioned by a leadscrew controlled by a DC 
motor with encoder feedback.  The registra-
tion plate is retracted by an air cylinder 
whenever the book moves in and out of the 
registration area.  It remains extended while 
the book is being jogged and squared.  On 
the left side of the table, a jogging plate at-
tached to an air cylinder pushes the book 
firmly into the registration plate.  The gripper 
moves forward slowly to bring the binding 
flush with the back fence on the gripper and 
therefore parallel to the face knife.  The grip-
per then clamps the book and accelerates to 
the trimming station. 

5.  The gripper moves the book to the proper 

cutting position for the face trim. 

6.  The knife and clamp assembly is driven by a 

hydraulic cylinder mounted to a cast iron 
frame underneath the table.  The clamp 
leads the knife and is powered by com-
pressed air captured in a set of air cylinders 

mounted to the clamp.  The air pressure to 
the clamp cylinders is adjustable at the rear 
of the machine. 

7.  The unload valve closes, preventing oil from 

flowing back to tank.  The cut valve opens 
allowing oil to fl

ow to the “down” port on the 

hydraulic cylinder.  A counterbalance valve 
on the cylinder prevents the knife assembly 
from moving until there is 900 PSI.  The 
knife assembly begins moving at 900 PSI.  
The pressure increases under load of cutting 
and clamping.  The system relief pressure is 
set from 1800-2000 PSI.  Oil is sent back to 
tank at this pressure setting. 

8.  The knife depth adjustment plunger actuates 

the knife slowdown sensor at approximately 
1/2 inch above the table.  When the sensor 
switches on, the computer adjusts a propor-
tional valve in the hydraulic manifold to slow 
the cutting mechanism in order to reduce 
shock when the mechanism hits the bottom 
of its stroke. 

9.  There are two knife-down switches, each 

comprised of a steel collar and an isolated 
stop block.  When the cutting mechanism 
reaches the bottom of its stroke, each stop 
block come in contact with its corresponding 
collar, thereby acting as a closed switch.  
When both switches are closed, the com-
puter knows that the cutting mechanism is 
down and should return up. 

10.  The direction of oil flow is reversed, causing 

the knife assembly to be sent up.  A sensor 
detects that the knife assembly is in the up 
position, at which point the unload valve 
opens. 

11.  The gripper rotates the book 90° counter-

clockwise in order to prepare for the bottom 
trim.  When the gripper is ready to rotate, a 
locking air cylinder releases, then a DC 
servo motor rotates the gripper to the proper 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды