manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 59

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

2-47 

2. Status Indicator RAPs

 

RAP 2.39 Left Jogger Retract Sensor 

Input 12 

The left jogger retract sensor detects that the left 
jogger cylinder is retracted.  The cylinder must 
be retracted before a book can be moved into 
the jogging station. 

Possible Fault Indicators 

 

“Left Jogger Failed to Ex-
tend/Retract”

 

message is dis-

played. 

Initial Actions 

Perform RAP 2.21 Left Jogger Cylinder to vali-
date operation of pneumatics. 

Check for loose or damaged wire 50 at the elec-
trical panel. 

Procedure 

1.  Switch the main power OFF and make sure 

that the jogger is fully retracted.  Retract the 
jogger cylinder by hand if necessary. 

2.  Switch the main power ON and go to the di-

agnostic screen (GP 6.2 Input/Output Diag-
nostics). Does the diagnostic screen show 
input “Left \ In” on? 

Y  N 

Short wire 50 to 74 at the main PWB.  On 
the diagnostic screen does input "Left In" 
switch on? 

Y  N 

Disconnect power and replace the con-
sole PWB (REP 4.24 Console PWB Re-
placement). 

Replace sensor (PL 5.17 Power Panel EE-
3503 (2/2)). 

3.  Disconnect wire 50 at the main PWB.  On 

the diagnostic screen does input "Left In" 
switch off? 

Y  N 

Disconnect power and replace the console 
PWB (REP 4.24 Console PWB Replace-
ment). 

4.  While still in the diagnostic screen, and with 

the jogger cylinder fully retracted, adjust the 
sensor.  To do this, loosen the sensor set 
screw and slide the sensor across its groove 
until the sensor LED switches on.  An audi-
ble beep should also be heard from the con-
sole as the sensor switches on and off. 

5.  Tighten the sensor set screw to lock the 

sensor in place. 

 

 

Figure 2-61. Jogger Retract Sensor 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды