manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 96

 

 

 

MAY 2019 

 

2. Status Indicator RAPs

 

2-84 

CMT-130TC Book Trimmer 

RAP 2.76 Stacker Pusher Cylinder 
Sensor 

Stacker I/O PWB Input 2 

The Stacker cylinder sensor detects when the 
pusher cylinder is in the partially extended posi-
tion.  This position is used to receive thin books 
from the roller tray. The sensor is attached to the 
pusher cylinder (Figure 2-116). 

Possible Fault Indicators 

 

“Stacker Push Position Error”

 

message is displayed. 

 

The pusher does not open to the right 
spacing to receive either thin books or 
thick books. 

Initial Actions 

Check that all cables between the trimmer and 
Stacker are securely fastened and are not dam-
aged. 

Check and repair loose or damaged wires 69, 
73, and 74 at the Stacker electrical panel. 

Procedure 

1.  Switch the main power ON and main air ON.  

Is the pusher cylinder partially extended, 
about half way out? 

Y  N 

Go to RAP 2.71 Stacker Pusher Cylinder. 

2.  Go to the Stacker diagnostic screen (GP 6.2 

Input/Output Diagnostics).  

Is input “Cyl. 

Prox

” on? 

Y  N 

Short wire 69 to 74.  On the diagnostic 
screen does input “Cyl. Prox” switch on? 

Y  N 

Disconnect power and replace the 
Stacker I/O PWB (REP 4.26 Accessory 
PWB Replacement). 

Adjust either the sensor or actuator magnet 
by loosening set screw in sensor or magnet 
and slide sensor or magnet until input 
comes on. If input still does not come on, re-
place defective switch (PL 5.64 Stacker 
Elec. Panel EE-3518). 

3.  Go to the Stacker diagnostic screen (GP 6.2 

Input/Output Diagnostics) and enable out-
puts.  Switch on output “Book Push”.  Does 
the pusher cylinder move toward the trimmer 
completely? 

Y  N 

Go to RAP 2.71 Stacker Pusher Cylinder. 

4.  On 

the diagnostic screen is input “Cyl. Prox” 

off? 

Y  N 

Disconnect wire 69.  On the diagnostic 
screen does input “Pusher Home” switch 
off? 

Y  N 

Disconnect power and replace the 
Stacker I/O PWB (REP 4.26 Accessory 
PWB Replacement). 

Replace defective switch (PL 5.64 Stacker 
Elec. Panel EE-3518). 

Repair complete. 

 

 

Figure 2-116. Pusher Cylinder Sensor 

 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды