manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 263

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

8-3 

8. Installation

 

8.4 Infeed Setup 

The CMT-130TC can be used either In-Line with 
a perfect binder or as a Stand-Alone Book Trim-
mer.  The following table lists the infeed options 
for each application. 

In-Line 

infeed options:

 

Option 1: 

Tilt Infeed Conveyor (56600TCA) 
+ Cooling Elevator (56421TCA) 

Option 2: 

Tilt Infeed Conveyor (56600TCA) 
+ Cooling Elevator (56421TCA) 
+ Pile Feeder (58500TCA-IL) 

Stand-Alone 

infeed options:

 

Option 3: 

Book Pile Feeder (58500TCA) 

Option 4: 

Standard Hand-feed Conveyor (59200) 

Option 5: 

Long Hand-feed Conveyor (56413B) 

The following procedures show how to setup 
each of the 5 infeed options. 

Infeed Option 1:  
Tilt Co Elevator 

 

 

Figure 8-4. Tilt Conv. + Elevator 

Setup Procedure 

1.  Position the Tilt Infeed Conveyor in front of 

the binder such that height-adjustable por-
tion of the conveyor is centered on the exit 
chute of the binder. 

 

Figure 8-5. Tilt Infeed Conveyor 

2.  The top of the conveyor belt at the right end 

of the tilt infeed conveyor should be set to 
about 13-7/8" (35.2 cm) from the floor and 
level (Figure 8-6).  Adjust the leveling pads 
as necessary. 

 

 

Figure 8-6. Height Adjustment 

3.  The height-adjustable portion should be set 

to the height of (or slightly below) the bottom 
of the binder's exit chute.  After adjusting the 
legs, lock into place with jam nuts. 

 

 

Figure 8-7. Adjustment Range 

4.  Move the entire conveyor close to the binder 

to minimize the distance between the adjust-
able conveyor and the binder's exit chute. 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды