manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 29

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

2-17 

2. Status Indicator RAPs

 

RAP 2.9 Status Light 

Outputs 1, 9, 20 

The status light is located on the top of the trim-
mer (Figure 2-8).  It indicates the current opera-
tional state of the trimmer.  The possible status 
light indications are as follows: 

Solid Green (output 1)

 - The trimmer is running 

and is ready to trim books or is trimming books. 

Flashing Yellow (output 20) 

- The trimmer is 

not running. Action must be taken to start the 
trimmer, for example the outfeed device needs 
to be emptied or the green start button needs to 
be pressed. 

Flashing Red (output 9)

 - There is an error in 

the trimmer or accessories that needs to be re-
solved before the trimmer will be able to run. 

The yellow status light is also used as an input 
diagnostic indicator.  While in the diagnostic 
screen, the status light toggles on and off each 
time an input changes states. 

Possible Fault Indicators 

 

Some or all of the colors of the status 
light do not switch on at the right time or 
at all. 

Initial Actions 

Check RAP 2.4 Input Power and RAP 2.5 DC 
Power. 

Check and repair loose or damaged wires 93, 
97, 99 at the electrical panel. 

Procedure 

1.  Switch the main power ON.  Go to the diag-

nostic screen and enable outputs (GP 6.2 
Input/Output Diagnostics).  Activate the sta-
tus light red, status light yellow, and status 
light red outputs.  Are output LED

’s 1, 9, and 

20 (GP 6.3 Input/Output LEDs) all switched 
on? 

Y  N 

Disconnect power and replace the main 
PWB (REP 4.23 Main PWB Replacement). 

2.  Deactivate all three status light outputs and 

exit the diagnostic screen.   

3.  Electrically activate the green status light by 

shorting wire 93 to 74.  Does the green sta-
tus light come on? 

Y  N 

Disconnect power and replace the status 
light (PL 5.13 Main Assembly 59000 
(13/14)). 

4.  Electrically activate the yellow status light by 

shorting wire 99 to 74.  Does the yellow sta-
tus light come on? 

Y  N 

Disconnect power and replace the status 
light (PL 5.13 Main Assembly 59000 
(13/14)). 

5.  Electrically activate the red status light by 

shorting wire 97 to 74.  Does the red status 
light come on? 

Y  N 

Disconnect power and replace the status 
light (PL 5.13 Main Assembly 59000 
(13/14)). 

6.  Disconnect power and replace the main 

PWB (REP 4.23 Main PWB Replacement). 

 

 

Figure 2-8. Status Light 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды