manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 8

 

 

 

MAY 2019 

 

Introduction

 

viii 

CMT-130TC Book Trimmer 

About this Manual 

This Service Manual is part of a multinational 
documentation system that includes service 
training.  It is intended to supplement service 
training with specific procedures and necessary 
reference information to efficiently service the 
CMT-130TC Book Trimmer. 

 

Organization 

This manual is divided into 7 sections.  The sec-
tions are outlined below: 

Section 1 

– Service Call Procedures 

This section outlines the strategy for success-
fully completing a service call. 

This section includes the following: 

 

Initial Actions 

 

System Checks 

 

Scheduled Maintenance 

 

Final Actions 

Section 2 

– Status Indicator RAPs 

This section contains Repair Analysis Proce-
dures (RAPs) necessary to repair faults.  Enu-
merated procedures are prefixed with RAP 2.x.  
The "2" refers to section number in this manual. 

Section 3 

– Book Quality 

This section contains procedures necessary to 
correct book trim quality issues.  Enumerated 
procedures are prefixed with the letters BQ 3.x.  
The "3" refers to the section number in this man-
ual. 

 

Section 4 

– Repairs/Adjustments 

This section contains detailed procedures for the 
repair and/or adjustment of mechanical and 
electrical components.  Enumerated procedures 
are prefixed with the letters ADJ 4.x or REP 4.x.  
The "4" refers to section number in this manual. 

Section 5 

– Parts List 

This section contains exploded view drawings 
and parts lists essential to the repair of the ma-
chine.  Enumerated drawings are prefixed with 
the letters PL 5.x.  The "5" refers to its section 
number in this manual. 

Section 6 

– General Procedures/Information 

This section contains general procedures, diag-
nostic information, product specifications, tag 
modification information, and other general infor-
mation.  General procedures are prefixed with 
the letters GP 6.x.  The "6" refers to its section 
number in this manual. 

Section 7 

– Wiring Data 

This section contains Block Schematic Drawings 
(BSDs) and wiring diagrams.  Diagrams are enu-
merated with the prefix WD 7.x. 

Section 8 

– Installation Instructions 

This section contains procedures necessary to 
install the CMT-130 and its accessories. 

 

Symbology and Nomenclature 

The following reference symbols are used 
throughout the documentation 

Warnings, Cautions, and Notes 

The formats of three specific types of notes 
found throughout this manual indicate the level 
of danger or importance associated with the task 
presented.  The format of warning notes, caution 

notes, and regular notes imply a certain level of 
danger.  The following examples give a descrip-
tion.  Associate the text format and symbol with 
its level of danger or importance. 

Warning Definition: 

WARNING 

A warning indicates an operating or mainte-
nance procedure that if not observed, could 
result in injury or loss of life. 

Caution Definition: 

CAUTION 

A Caution with this symbol indicates an operat-
ing or maintenance procedure that if not ob-
served, could result in damage to equipment. 

ESD Caution Definition: 

CAUTION 

A Caution with this symbol indicates an operat-
ing or maintenance procedure that if not ob-
served, could result in damage due to electro-
static discharge. 

Note Definition: 

Note:  A regular note indicates an operating, 
maintenance procedure that can be helpful, yet 
is not required. 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды