manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 26

 

 

 

MAY 2019 

 

2. Status Indicator RAPs

 

2-14 

CMT-130TC Book Trimmer 

RAP 2.6 Touch Screen Display 

The touch screen display comes on when power 
is switched on.  It remains on until a time of inac-
tivity is reached that is equal to the sleep timer 
setting. 

Possible Fault Indicators 

 

The touch screen display does not come 
on. 

 

The LED lights do not switch on. 

 

“Connection Lost to I/O Motor 
Controller!”

 

message appears re-

peatedly.  

Initial Actions 

Check that all cables are connected securely at 
the back of the console.  Check that the cables 
connecting the console to the main PWB are 
connected securely at the main PWB. 

The touch screen display and the enclosure fans 
are powered from the same source (120 VAC). 
Switch the main power ON to check if the touch 
screen display comes on.  If the enclosure fans 
also do not turn on, go to RAP 2.4 Input Power 
to troubleshoot the input power. 

Procedure 

1.  Is there 120 VAC between display panel 

wires 21 and 22 (Figure 2-5)? 

Y  N 

Check loose or damaged wires 21 and 22. 
Go to RAP 2.4 Input Power. 

2.  Is there 16 VAC between the two blue wires 

and also 18 VAC between the two red wires 
(Figure 2-5)? 

Y  N 

Replace transformer on console (PL 5.18 
Control Console EE-3456-6). 

3.  Check fuses PCF1 and PCF2 (Figure 2-5).  

Is resistance less than 2 Ohms on both 
fuses? 

Y  N 

Replace fuse. 

4.  Disconnect main power and replace the dis-

play PWB (REP 4.24 Console PWB Re-
placement). 

 

Figure 2-5. Display Console 

– Rear Side 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды