Challenge 130TC-A-160000 Скачать руководство пользователя страница 233 | Manualshive

Страница: 233 / 282

background image

MAY 2019

CMT-130TC Book Trimmer

6-19

6. General Procedures/Information

GP 6.16 Specifications

WARNING

The CMT-130TC was designed specifically
for use with the Challenge infeed and exit ac-
cessories. If any other accessories are used,
it is the purchaser's responsibility to comply
with ANSI B65.4 Safety Standard for Three-
Knife Trimmers. Failure to comply with this
standard could result in personal injury or
death.

CAUTION

The CMT-130TC was specifically designed to
trim perfect bound books only. Trimming
other materials with the CMT-130TC may result
in safety hazards or damage to the machine.

For trimmable book sizes, see GP 6.17 Book
Size Chart.

Multiple Book Mode: Note that up to 3 books
may be stacked in multiple book mode. The to-
tal thickness is not to exceed 1-1/4 in. (32 mm).
Larger pile thicknesses may be cut, but the trim
may be less accurate and more out-of-square.
Always test before running books outside the
published specifications.

Sound Emission:

A-weighted sound pressure level measured in
an enclosed room at operator level (6 feet/183
cm):
Machine in idle state: 62 dB
Machine trimming: 75 dB

NOTE: Challenge reserves the right to make
changes to any product or specification without
notice and without incurring responsibility to ex-
isting units.

Description

US Units

Metric Units

Max. start book

13.00 (spine) x 9.50 in.

330.2 (spine) x 241.3 mm

Min. start book, off-line (Hand-Feed)

7.00 (spine) x 5.00 in.

177.8 (spine) x 127.0 mm

Min. start book, near-line (Pile Feeder)

7.00 (spine) x 5.00 in. (single book mode)

7.00 (spine) x 6.75 in. (multi-book mode)

177.8 (spine) x 127.0 mm
177.8 (spine) x 171.4 mm

Min. start book, in-line (Tilt + Elevator)

7.00 (spine) x 6.75 in. (single book mode)

7.00 (spine) x 7.00 in. (multi-book mode)

177.8 (spine) x 171.4 mm
177.8 (spine) x 177.8 mm

Min. finish book

5.82 (spine) x 4.00 in.

147.8 (spine) x 101.6 mm

Max. finish book

12.00 (spine) x 9.00 in.

304.8 (spine) x 228.6 mm

Max. face (fore-edge) trim

5.50 in.

139.7 mm

Max. top (head) trim

6.00 in.

152.4 mm

Book thickness range

0.10 to 2.00 in.

2.5 to 50.8 mm

Min. Trim

0.10 in.

2.5 mm

CMT-130TC Basic Machine

Width

52 in.

132 cm

Depth

57 in.

145 cm

Height

60 in.

152 cm

Net Weight

1,500 lb.

680 kg

Shipping Weight

1,800 lb.

816 kg

Floor Loading

53 PSI

3.7 kg/cm

2

Optional Waste Bin Capacity

43 gal.

164 L

Oil Capacity

5 gal.

19 L

Air Consumption

5 CFM @ 90 PSI

142 LPM @ 620 kPa

Knife Re-grind

1/4 in.

6.4 mm

Memory

99 jobs

Time to change book size

10 sec. or less

Throughput

up to 200 books/hr. (single book mode)

up to 500 books/hr. (multi-book mode)

Electrical Requirements

60 Hz Machines

60 Hz, AC, 3 phase, 208/230 Volts, 20 Amps (service size 30 Amps)

50 Hz Machines

50 Hz, AC, 3 phase, 380/415 Volts, 16.5 Amps (service size 20 Amps)

50 Hz, AC, 3 phase, 200-208 Volts, 20 Amps (service size 30 Amps)

56600TCA Tilt Infeed Conveyor

(150 lb/68 kg net) (230 lb/105 kg ship) (5.62 PSI/.40 kg/cm

2

load)

Height x Width x Depth

26 x 39 x 29 in.

66 x 99 x 74 cm

Compatible binder exit heights:

17 to 26 in.

43 to 66 cm

56421TCA Cooling Elevator

(335 lb/152 kg net) (470 lb/214 kg ship) (11.86 PSI/.83 kg/cm

2

load)

Height x Width x Depth

46 x 38 x 22 in.

117 x 97 x 56 cm

58500TCA Book Pile Feeder

(370 lb/168 kg net) (420 lb/191 kg ship) (13.1 PSI/.92 kg/cm

2

load)

Height x Width x Depth

54 x 21 x 57 in.

137 x 53 x 145 cm

59200 Standard Hand Feed Conveyor

(40 lb/18.2 kg net) (80 lb/36.4 kg ship) (3.2 PSI/.22 kg/cm

2

load)

Height x Width x Depth

11 x 16 x 15 in.

28 x 41 x 38 cm

56413B Long Hand Feed Conveyor

(95 lb/43 kg net) (220 lb/100 kg ship) (7.6 PSI/.53 kg/cm

2

load)

Height x Width x Depth

42 x 35 x 13 in.

107 x 89 x 33 cm

58000TCA Vertical Stacker

(218 lb/99 kg net) (268 lb/122 kg ship) (7.7 PSI/.54 kg/cm

2

load)

Height x Width x Depth

44 x 19 x 49 in.

112 x 48 x 124 cm

56420TCA Exit Conveyor

(85 lb/39 kg net) (210 lb/95 kg ship) (6.76 PSI/.48 kg/cm

2

load)

Height x Width x Depth

39 x 47 x 13 in.

99 x 120 x 33 cm

59093 Exit Ramp

(6 lb/ 3 kg net)

Height x Width x Depth

5 x 10 x 12 in.

13 x 25 x 30 cm

Note: See Operator’s Manual for floor space requirements of the CMT-130TC with various option configurations.

«
...
231
232
233
234
235
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: Makita Страницы: 9

Бренд: Makita Страницы: 20

Бренд: Makita Страницы: 20

Бренд: Makita Страницы: 48

Бренд: Makita Страницы: 20

Бренд: Makita Страницы: 56

Бренд: Makita Страницы: 18

Бренд: Makita Страницы: 26

Бренд: Makita Страницы: 16

Бренд: Makita Страницы: 16

Бренд: Makita Страницы: 9

4050, 4850, 5550, 6350

Бренд: Makita Страницы: 7

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 232

Бренд: Makita Страницы: 4

Бренд: Echo Страницы: 27

Бренд: Remington Страницы: 56

Бренд: DMX4ALL Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды