Challenge 130TC-A-160000 Скачать руководство пользователя страница 97

Страница: 97 / 282

MAY 2019

CMT-130TC Book Trimmer

2-85

2. Status Indicator RAPs

RAP 2.77 Stacker Tray Full Sensor

Stacker I/O PWB Input 6

The tray full sensor

detects when the Stacker’s

delivery bed is full of books. It senses the slid-
ing back stop when it is at the outermost posi-
tion.

The sensor is located near the end of the deliv-
ery bed, under the narrow side cover (Figure
2-117).

Possible Fault Indicators



“Stacker Output Full”

message

is displayed, but the delivery bed is not
full.



The Stacker continues to accept books,
even when the delivery bed is full.

Initial Actions

Check that all cables between the trimmer and
Stacker are securely fastened and are not dam-
aged.

Check and repair loose or damaged wires 68,
73, and 74 at the Stacker electrical panel (Figure
2-118).

Procedure

1. Remove all books from the Stacker and

slide the back stop all the way forward, away
from the front end of the stacker.

2. Switch the main power ON and go to the

Stacker diagnostic screen (GP 6.2 In-
put/Output Diagnostics

). Is input “Tray Full

Prox” off?

Y N

Disconnect wire 68. On the diagnostic
screen does input “Tray Full Prox” switch
off?

Y N

Disconnect power and replace the
Stacker I/O PWB (REP 4.26 Accessory
PWB Replacement).

Adjust the sensor (GP 6.5 Proximity Sen-
sors) and replace if faulty (PL 5.59 Outfeed
Stacker 58000TCA (5/9) or PL 5.64 Stacker
Elec. Panel EE-3518).

3. Short wire 68 to 74. On the diagnostic

screen does input “Tray Full Prox” switch
on?

Y N

Disconnect power and replace the Stacker
I/O PWB (REP 4.26 Accessory PWB Re-
placement).

4. Adjust the sensor (GP 6.5 Proximity Sen-

sors) and replace if faulty (PL 5.59 Outfeed
Stacker 58000TCA (5/9) or PL 5.64 Stacker
Elec. Panel EE-3518).

Figure 2-117. Stacker Tray Full Sensor

Figure 2-118. Stacker Electrical Panel

Содержание 130TC-A-160000



























































































































































































































































































Результаты поиска

Содержание 130TC-A-160000

Отзывы:

Похожие инструкции для 130TC-A-160000

Бренды по названию

Популярные бренды

Challenge 130TC-A-160000, Руководство по обслуживанию

Результаты поиска

Содержание 130TC-A-160000

Отзывы:

Похожие инструкции для 130TC-A-160000

Бренды по названию

Популярные бренды